Question about Mazda 626

Open Question

Mazda 626 1990 GD 2.2.litre automatic rough idle, sometimes stalls at traffic lights

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mnabi01
  • 94 Answers

SOURCE: 2004 mazda 3 stalls off idle

i found out from dealer there was a service bulitan for this problem. mazda reprogram the ecm for idle speed contorol . problem solved.

thank you

Posted on Jan 28, 2009

Ad
rockitman187
  • 2559 Answers

SOURCE: 1995 mazda 626 stalling at low idle

Check the EGR valve



Please rate this a fixya

Posted on Feb 11, 2009

ourhowse
  • 2007 Answers

SOURCE: mazda rx8 rough idle and stalls when at operating

If there are no vacuum leaks, change idle control sensor.

Posted on Jul 28, 2009

  • 135 Answers

SOURCE: My 2002 Mazda 626 idles rough and cuts off alot

Pull your vacuum line off your fuel pressure regulator and see if it smells like gas in line or if gas runs out of the line.

Posted on Aug 04, 2009

  • 1 Answer

SOURCE: 91 mazda 626 erractic idle surge when engine is cold

My '91 626 did the same thing. I tested the throttle position sensor, and it was good so that wasn't it. The other likely culprit is the Idle Speed Control valve, or Idle Air Control valve, which is a $500 part new (more than I paid for the whole car). I pulled one off a 626 at the salvage yard and got it for 3 bucks, put it on (it's an easy DIY, just 4 philips screws holding it to the intake manifold), however I can't be sure that solved the problem, since I haven't run the car much since then. It would seem the most likely cause, tho, and a cheap fix if you go used. Other possibilities: O2 sensor or Mass Air Flow sensor?

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Mazda 626 RPM dropping problems and then engine stalls with no engine code thrown


Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Sep 07, 2012 | Cars & Trucks

1 Answer

2000 MAZDA 626 LX 2.0 tries to die at lights or stop signs. Runs fine otherwise.


Engine stalling and rough run issue at low speeds

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Aug 06, 2012 | 2000 Mazda 626

2 Answers

I have a 2001 mazda 626 and at certain times when i come to a stop it will idle eratic or stall. I will then have to start my car. This is not everytime. My check engine light came on with the code of a...


check connection to cam sensor. sometimes corrosion will cause a poor electrical connection. clean as needed. otherwise you may have to replace the sensor.

Sep 18, 2010 | 2001 Mazda 626

1 Answer

I have a 4 liter V6 2003 Ford Explorer ( 2 door). The check engine came on and then it started idling rough. When it idles rough the AC blows hot. Recently it has started stalling when idling at a...


Hello! Most probable cause is a leak in the vacuum line or broken elbow connection to the Positive Crankcase Ventilation (PCV) valve...Check PCV and its vacuum line...Send results...

Guru..............saailer

Aug 27, 2010 | 2003 Ford Explorer

1 Answer

Rough idle when stopped in drive


hi barry i have the same problem did you ever fix yours ?

Sep 30, 2009 | 1995 Mazda Protege

1 Answer

Engine stalls ,hard to startrun rough


Service Engine light came on and stays on and this is on my 1995 Grand Marquis LS 4.6 litre Engine. It is now idling a little rough

Sep 09, 2009 | Mercury Grand Marquis Cars & Trucks

1 Answer

Rough shifting


It sounds like the MAP (manifold absolute pressure) switch might be bad. Since the check engine light is on, have the computer codes read.

Jul 21, 2009 | 2003 Mazda Protege

1 Answer

2004 mazda 3 stalls off idle


i found out from dealer there was a service bulitan for this problem. mazda reprogram the ecm for idle speed contorol . problem solved.

thank you

Jan 27, 2009 | 2004 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...