Question about 2004 Jeep Grand Cherokee

1 Answer

How do i know which of the 4 different types of ball joint i rquire for my 2004 jeep grand cherokee limited?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 11,800 Answers

Once you have identified the worn part just remove it from the car and go with it to a parts shop and ask for an identical replacement.

Posted on Jul 31, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

What is differential fluid

differential fluid is typically called 80w 90 (or similar designation based on manufacturer specs.) but is very different from the grease used in ball joints. you should check your owner's manual for specific specifications, but typically a good NLGI listed wheel bearing grease applied through the grease fittings on the ball joints will properly lube the ball joints

Dec 29, 2012 | 2000 Jeep Grand Cherokee

1 Answer

1997 Jeep grand Cherokee limited 5.2l to fix very stiff steering. I have changed the power steering pump already an it is still hard to turn my wheels

sound like lack of lubrication at the steering joints, your ball joints need greasing and make sure you bleed power steering system, check power steering fluid level.if low more like power steering system full of air need bleeding.

Jan 25, 2012 | 1997 Jeep Grand Cherokee

2 Answers

How do i know which ball joints i need for my 2004 jeep grand cherokee limited?

Lift the car from the ground and secure it, ask a big friend to shake the wheels and other suspension elements and you look for loose parts - see it = replace it.

Jul 31, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Grand cherokee WJ 2004 SE V8 Steering

There are "special" ball joints with a built in off-set that can be used to correct that. There are a few, each having a different built in amount of offset, so you need to know how much correction you need. Camber usually does not change except if the axle itself is bent. However I am wondering if the wheel mount flange is slightly bent. Did anyone check the side run- out there to see if it changes when the tire assembly is turned? What about side play in the ball joints?

Mar 14, 2010 | 2000 Jeep Grand Cherokee

1 Answer

97 jeep grand cherokee limited shakes at high speed

-Tires need to be rebalanced, tire weight missing
-excessive tire wear from not rotating tire.
-Play in tie rods.
-CV joints are worn.
-wear in upper or lower ball joints.
-excessive wear in u-joint.

Aug 16, 2009 | 1997 Jeep Grand Cherokee

1 Answer

2004 jeep grand cherokee. I am doing the rear

first. i don't know why you would have ball joints in the rear end. it is not a steering axle. don't do it. your gona get hurt. take it in and let a machanic work on it. second you don't take the shocks or springs out to replace ball joints. just the wheel assembly comes off. and yes i believe there are alighnment adjustments for the rear. but i wouldn't do that at home myself. take it in.

Aug 13, 2009 | 1995 Jeep Grand Cherokee

1 Answer

How to change the ball joints on a 1996 jeep grand cherokee

'dont remember any. Be sure you have the joint square with the knuckle when installing... If it cocks to one side, it will jam. take care not to damage the boot. When using fork, it can damage stuff . I refrain from using it as much as possible, using a good sized hammer and giving a shot on the side of pin recievers (like where tie rod end goes through arm on knuckle) this saves tearing tie rod end boot. When in doubt get a manual...any more questions, ask!!

Mar 14, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Replacing a '98 Grand Cherokees ball joints

The only parts you need are the ball joints, upper and lower, a total of 4, if you need all 4. As far as tools, you'll need wrenches, a removal and installer tool, the ball joints are pressed into the control arms, and a ball joint to steering knuckle seperator tool.Without those special tools, you will never get them changed, if you do it yourself.

Mar 12, 2009 | 1998 Jeep Grand Cherokee

1 Answer

1999 jeep grand cherokee limited

Remove the brake parts tie the brake caliper out of the way, break loose the tie rod and lower ball joint, move the steering knuckle out of the way, pull the axle straight out with a sharp snap motion.

Jul 03, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides