Question about 2001 Ford Crown Victoria

Open Question

2000 crown vic no power to blower motor, fuses good, reostat no power going in and no power to any of wiring leading into harnesses

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 39 Answers

SOURCE: wiring harness on 03 crown vic police car

First take it to another reputable shop, tell them what the first shop found and that it is to expensive. In these economic times 99% of shops will beat that price. If the wiring harness is bad (by the price I'm assuming it's the main harness) there's not much you can do. My guess is the wires have worn from vibration and are shorting out to one another. You could ask the shop if they could pinpoint the shorted wires, cut them out and solder in new wires. However my guess is no shop will do this due to liability and if they do, there will be no guarantees or warranty on the service.

Posted on Apr 02, 2009

Ad
  • 5546 Answers

SOURCE: Wiper motor replacement for a 99 crown vic

I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

Posted on May 06, 2009

gandergmm
  • 145 Answers

SOURCE: hvac blower not operating any speed,

have you tried replacing the blower resister module?

Posted on Oct 01, 2009

dsakrison1
  • 65 Answers

SOURCE: 2000 crown vic police interceptor bypass a/c clutch pulley

you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Posted on Oct 06, 2009

roniecon
  • 6927 Answers

SOURCE: 2001 Crown vic LX Sport..Blower motor inop car has

The blower motor might be bad,turn it on,high blower,and bump the blower motor body with the palm of your hand,if it starts to run,or tries to run,then replace the blower motor.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 ford crown vic heater/ac fan switch doesn't blow anything at all on all speeds


you need to replace the blower resistor...90 percent of the time that will be the problem in your situation...before replacing it..check for power to blower motor first...if it has power then replace blower motor if not its the resistor

Nov 17, 2013 | 2000 Ford Crown Victoria

1 Answer

Where does the ignition switch and fuse panel get its power from? 4 dead fuses, not blown.


I have found with these Crown Vic's,especially police cars,they manage when the get in accidents to hit the right front of the cars and when they do they damage the wiring harness. The rain,salt,snow get in the harness and you eventually have problems. Look under the car in front of the right front tire and you'll see. Good size wiring harness. Look at it for damage,or sometimes you'll see like a light green dust coming out of the harness. Usually where I find my breaks,shorts or opens.

Apr 06, 2013 | 2004 Ford Crown Victoria

1 Answer

Fuse for AC blower on a 2004 Ford Crown Victoria


fuse loction for blower motor on a 2004 ford crown vic

Jun 19, 2012 | Ford Crown Victoria Cars & Trucks

1 Answer

The blower motor on my 2005 Chevy Trailblazer is not getting any power. I've installed a new blower motor, and resistor. The fuses and relays are good, and the compressor works, but there is no power going...


try checking for a 12v feed to the motor and iam sure you will find one ,i think the problem is the earth as the earth is the one that controls the speed via the reostat and the control knob ,so if its works with an earth then its either the reostat or the control switch

Jun 12, 2010 | 2005 Chevrolet TrailBlazer

2 Answers

I have an 02 crown vic and now the blower motor just quit working i put a new motor on it and checked the fuse but it still dont work ive been reading up and there seems to be alot of peolpe saying the...


On my 2004 Ford Crown Vic One day it just stoped blowing no A/C or heat i checked all the fuses and relays and they are fine so i guess its the blower motor and i want to know the location and if is easy to chang \??? Or if might be somthing else ccan you help???

May 22, 2010 | 2004 Ford Crown Victoria

1 Answer

2005 Crown Vic climat contr fan not working Fuses good Motor good


does it have a digital control panel? As this uses an electronic blower speed controller located at the engine compartment (rear engine block) fix on ac phlenum try to shake the connector or wire while the system is on.

Jan 31, 2010 | 2005 Ford Crown Victoria

2 Answers

2000 dodge caravan, blower motor not running


first check fuses then go over to passenger side under the dash find the two twisted wires that lead to the blower motor, unplug them, and test the harness end for power, if power is present replace blower motor.

Jan 21, 2010 | 2000 Dodge Caravan

2 Answers

Hvac blower not operating any speed,


have you tried replacing the blower resister module?

Sep 29, 2009 | 2003 Ford Crown Victoria

1 Answer

Can't start my cron vic 1998 battery sign comes on and off but battery is good alternater is good


i have a 1999 Ford Crown Victoria Police Interceptor. you have a short in your wiring harness leading to your battery. this happens every time with these cars, good battery-good starter-good alternator but car still wont turn over because the power from the battery isnt able go directly to the motor. check your relay circuits and harness.

Jul 26, 2009 | 1998 Ford Crown Victoria

1 Answer

1994 crown vic where is engine computer located im getting parts off another car what other parts be good to save


Look for a wiring harness on the passenger side of the car that leads to the right side of the dashboard - up underneath it - it should lead you to a rectangular aluminum box. That's your computer.

Jun 12, 2009 | 1994 Ford Crown Victoria

Not finding what you are looking for?
2001 Ford Crown Victoria Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...