Question about Chevrolet Avalanche

3 Answers

HOW DO I CHANGE THE HEADLAMP BULB ON MY 07 AVALANCHE

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 170 Answers

Open the hood and locate the rear of the headlight. the bulb is inside a light assembly and can be accessed from under the hood . some are secured with a small piece of wire, but the rest are secured with a twist lock ring / or just the standard bulb socket. twist them and pull GENTLY to access the bulb. just remember DO NOT ALLOW your OILY fingers to touch the new bulb. use tissues to keep the oils off your bulbs. then re secure the bulb into the fixture

Posted on Jul 31, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,513 Answers

Hi

Open the hood and you'll find two "twist and turn" large plastic hand operable screws that when loosened will allow you to remove the entire light assembly. That will allow you to change the head lamp. Install in reverse.
Access the bulb from the rear of the headlight assembly. Squeeze the clip, and turn it counter clock wise, and pull it out. Pull the bulb out, and replace. Be sure not to touch the new bulb with bare fingers. The natural oil on your fingers will cause the bulb to prematurely fail.

Let us know if you have something more to know else accept the suggestion.
Thank You for contacting Fixya.com

Posted on Jul 31, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 40 Answers

There are two rods one on each side, silver in color or black, just twist and lift them right out. the light will then just come right out

Posted on Jul 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove bulb from socket for day time running light on 2002 avalanche


dak408_133.gif
  1. Open the hood.
  2. Remove the park/turn signal lamp assembly.
  3. Remove the headlamp retainer pins.
  4. Pull out the headlamp assembly in order to access the electrical connector.
  5. Disconnect the electrical connector.
  6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.
INSTALLATION PROCEDURE

IMPORTANT:
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.
  1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
  2. Connect the electrical connector to the bulb.
  3. Install the headlamp assembly.
  4. Install the headlamp retainer pins.
  5. Rotate and lock the pins in place.
  6. Install the park/turn signal lamp assembly.
  7. Inspect the operation.

Dec 11, 2010 | 2002 Chevrolet Avalanche

1 Answer

How to change the headlight bulb on 2009 gmc sierra driver side


1. Loosen only, do not remove, the lower outside hidden headlamp bolt (2). 2. Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support. 3. Pull the lamp assembly slightly forward to access the electrical connection. 4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
Headlamp Screws (Qty: 2)
1 Caution: Refer to Fastener Caution .
6 Nm (53 lb in)
O Headlamp Screw (Hidden)
6 Nm (53 lb in)
3 Headlamp Housing Support


Preliminary Procedure Remove Healamp
Remove either the LF or RF headlamp assembly. Refer to Headlamp Replacement (Chevrolet) Headlamp Replacement (GMC HD)
Headlamp Replacement (HD Diesel).
Headlamp Bulb (Hi)
Warning: Refer to Haiogen Bulb Warning .
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.
Headlamp Bulb (Lo)
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.

Need more come to https://www.autorepairhelp.us


change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-0.png change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-1.png

Aug 14, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

1 Answer

How do you replace the passenger side low beam on a Pontiac Grand Prix '07? I can't get to it from the back, so I'm wondering if there is a special tool to take off the front lens.


raise the hood. lift upward on the headlamp retainer(its a off white color tab right behind the lamp asm.in about the middle of lamp)pull the headlamp asm. outwardenough to release the headlamp asm from the upper fascia support.position the headlamp asm. away from the vehicle body to access the electrical connector. disconnect the electrical connector from headlamp asm.remove headlam asm. from vehicle. remove headlamp bulb /socket from the headlamp ,by turning counter clockwise. remove headlamp bulb/socket from the headlamp asm. install new bulb in socket and reverse procidure .

Feb 22, 2010 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

How to change front headlamp bulb? Low beam


  1. Open the hood.
  2. Remove Grille.
  3. Remove the 2 retainers on back of headlamp assembly and remove the headlamp from the sheet metal panel.
  4. Remove the access cover from the rear of the headlamp.
  5. Disconnect the electrical connector from the socket.
  6. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  7. Disconnect the electrical connector from the socket.
  8. Remove the bulb and socket from the headlamp.
Installation Procedure Important: • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket. • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.

Oct 14, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

07 max headlight, what is that piece called that locks the bulb in place?


In the Nissan service manual it is called the "Headlamp Bulb Plastic Cap". This part covers the bulb. Then you twist the bulb socket to remove the bulb.

Jul 29, 2009 | 2007 Nissan Maxima 3.5 Sl Sedan

1 Answer

I need to change a dead bulb in my headlights and I dont have the owner manual.


96 sable, only ino I have. should be similar. Please rate, thanks

  1. sth~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    NOTE: A properly aimed headlamp (13008) assembly normally need not be re-aimed after installation of bulb. A burned out headlamp bulb and retainer (13N021) should not be removed from the headlamp until just before a replacement headlamp bulb and retainer is to be installed. Removal of a headlamp bulb and retainer for an extended period of time may allow contaminants (dust, moisture, smoke) to enter the headlamp and affect the performance of the headlamp. When servicing the headlamp bulb and retainer, energize the headlamp bulb and retainer only while it is contained within the headlamp body.

    Make sure headlamp switch (11654) is in OFF position.
  1. NOTE: On some models the clamps holding the integrated relay control module (IRCM) may need to be unsnapped and the module pulled aside to gain access to the driver side bulb.

    Open hood and locate headlamp bulb through hole in upper radiator support assembly.
  1. Remove headlamp wire connector from headlamp bulb and retainer by pulling the connector and wires in a rearward direction.
  1. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding headlamp bulb retainer off headlamp bulb and retainer. Keep headlamp bulb retainer as it will be used again to retain new headlamp bulb and retainer.
  1. Carefully remove headlamp bulb and retainer from opening in headlamp bulb (13007) by gently pulling straight out of opening. Do not rotate headlamp bulb and retainer during removal.
0a1a11c.gif

Jul 05, 2009 | 1991 Mercury Sable

1 Answer

I have 2006 Grand Prix How do I change head lamp?


Caution Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:
Turn off the lamp switch and allow the bulb to cool before changing the bulb.
Leave the lamp switch OFF until the bulb change is complete. Always wear eye protection when changing a halogen bulb. Handle the bulb only by its base. Avoid touching the glass. Keep dirt and moisture off the bulb. Properly dispose of the used bulb. Keep halogen bulbs out of the reach of children.
Raise the hood.
Remove the headlamp assembly bolts from the upper fascia support.
Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support.
Position the headlamp assembly away from the vehicle body to access the electrical connector.
Disconnect the electrical connector from the headlamp assembly.
Remove the headlamp assembly from the vehicle.
Disconnect the electrical connector from the headlamp bulb/socket.
Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise.
Remove the headlamp bulb/socket from the headlamp assembly.

Jun 13, 2009 | 2006 Pontiac Grand Prix

1 Answer

How do i change both headlights on my 2002 chevy cavillier


Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Hood close out filler panel.
    • Bolts from the headlamp.
    • Headlamp from the headlamp mounting panel.
    • Electrical connector from the headlamp.
    • Headlamp bulb/socket retainer ring from the headlamp.
c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    Hi, I have a 99 mercury cougar and I need to change the headlights. I am having difficulty finding the electrical connector so that I can pull the headlight assembly out and change the lights. Where is...


    Headlamp Bulb Removal
    1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly .

    Headlamp Assembly Removal
    1. Remove the radiator grille.7feecfa.gif

    Remove the headlamp assembly.
    2b42ecf.gif
    remove the cover/
    1. f76b11b.gif
    3.
    sxu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not touch the glass of the bulb with your fingers.
    Remove the headlamp bulb (low beam bulb shown). 79891b8.gif

    Jan 10, 2009 | 1999 Mercury Cougar

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    146 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8266 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...