Question about Lexus ES 300

2 Answers

I like to keep working with Mr,MN.Fisherman,He help me befour.Mr.Fisherman I need instructionss on the Instalation of the window regulator on my Lexus ES300 same front passanger door. Tank you.

Posted by on

  • gerquiaga Aug 02, 2010

    My comment is that I never got an answer to my
    request for help on the Installassion of the
    Regulator motor on the door of the front passanger window on my 1996 Lexus ES300, Tanks.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

1. Remove the door panel by removing all the screws, lock and window controls and then gently pry it loose. After it is loose, lift it up and off.
2. Locate and remove the bolts holding the regulator to the door; it is likely you will have to manually lower the window in order to access the bolts.
3. Remove the old regulator, disconnect all wiring and replace the old regulator with a new one you have purchased from a parts supplier. Shop online to find the best value as you will pay a mint if you order one through a dealership.
4. Tighten the bolts holding the new regulator and reinstall the moisture barrier. Make sure all the wires are put back in the door before closing the door panel.
5. Engage the power window switch and the new regulator should work unimpeded.

Posted on Aug 02, 2010

  • 4 more comments 
  • gerquiaga Aug 10, 2010

    I have the install the regulator,but the problem now is that, the cable needs to be sincronized, or timed whith the regulator wheel in which it coils arraund maybe y need tu turn the regulator up or down tu certain possition, I need more of your good help, I am stuck.

  • gerquiaga Aug 10, 2010

    I have the install the regulator,but the problem now is that, the cable needs to be sincronized, or timed whith the regulator wheel in which it coils arraund maybe y need tu turn the regulator up or down tu certain possition, I need more of your good help, I am stuck.

  • gerquiaga Aug 10, 2010

    I have the install the regulator,but the problem now is that, the cable needs to be sincronized, or timed whith the regulator wheel in which it coils arraund maybe y need tu turn the regulator up or down tu certain possition, I need more of your good help, I am stuck.

  • gerquiaga Aug 10, 2010

    I have the install the regulator,but the problem now is that, the cable needs to be sincronized, or timed whith the regulator wheel in which it coils arraund maybe y need tu turn the regulator up or down tu certain possition, I need more of your good help, I am stuck.

  • gerquiaga Aug 11, 2010

    Please unser my added coment to your last instrccions. Tanks

  • Nate Stansfield
    Nate Stansfield Aug 11, 2010

    Place inner panel cam (rear of new front side door window regulator
    assembly) into opening in inner door panel, before riveting front side
    door window regulator assembly into place.
    Position front side door window regulator assembly backplate to inner door panel and install rivets. Regulators should be in the same position as window sits when installing. If window is down, run regulator to the down position before installing. If window was all the way up, pu tregulator in upward position.


×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,016 Answers

Look for him in the find experts area........this should find him.

Posted on Jul 31, 2010

  • Jason Maurirere
    Jason Maurirere Aug 07, 2010

    Hi did you ever get to find the expert you were after?

  • Jason Maurirere
    Jason Maurirere Aug 09, 2010

    Do you need to know how too install a window regulator for your Lexus?



×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which battery for my wellcraft 180 Fisherman


you need to check the manual for the engine. get the cold cranking amps. I run two batteries with dual battery switch so you can isolate the batteries from each other or double up on cold days. don't get a car battery as it wont hold up to the pounding get a deep cycle marine battery

Apr 17, 2014 | Cars & Trucks

1 Answer

Toyota corolla side window


The driver switch is called the master switch. When replacing this unit you need to perform what's called a ( relearn ). Turn the ignition switch to position 2 so that the dash lights come on. Then hold the window switch in the down position and keep holding it down for 10 seconds after the window is all the way down. Then make the window go fully up and hold the bottom up for 10 seconds after the window closes . Sometimes you my need to do this a few times to make it relearn . This performed properly should give you full operation of the windows. FYI. This may need to be done on every door. . This will also need to be done if you replace a window regulator of any door or door windows you replace.
Hope this helps. Mr Toofix

Jan 27, 2014 | Cars & Trucks

1 Answer

When i roll the drivers side window down, on my 2000 suzuki esteem wagon, the windew comes out of the up& down channels. ...i have put the window back in the channel, but it wont stay there. can you...


More than likely, the window regulator will need to be replaced. The regulator is the assembly in the door that the window rides on, and it has guides to keep the window in line. More than likely one or more of the guides are bent or broken. This is a pretty common wear item.
To replace the regulator, you have to remove the door panel, then the window glass, then the regulator assembly. These are usually very tricky to remove as there is not much room to work in there. They can also be dangerous if you are not careful. There have been instances of people losing fingers when attempting to change a window regulator. Though this was mostly on older cars with manual windows. Just be careful!
Hope this helps!

May 10, 2011 | 2000 Suzuki Esteem

1 Answer

Driver side back window keeps falling down.a thin metal wire with an end that seems to come out out of a slot somewhere


This is so common on this car, you will need to replace the window regulator and sometimes the window clips break that bolt window to regulator, i will enclose a picture of the window regulator to show you, hope this helps.johnjohn2_22.jpg

Nov 16, 2010 | 1999 Oldsmobile Intrigue

1 Answer

1999 Silverado 1500: fuel pressure regulator instalation...


Remove vacuum hose, find schrader valve and bleed off fuel pressure, pull out lock ring, remove regulator, install in reverse

May 16, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Electric window on pasenger drivers side does not stay up on 97 Buick Regal.


Hello there:
There is a window regulator that is attached to the window motor that keeps the window in place.
You will need to remove the dorro panel and remove the window regulator and replace it with a new one and this will solve your problem ok?
Hope this is very helpful for you
Best regards Michael

Dec 03, 2009 | Buick Regal Cars & Trucks

1 Answer

Window wont open


It could be something else other than just the regulator or motor, please keep this in mind. So as not to be repetitive, for the failure of your power window, review this handy diagnostic article, which identifies the possible causes, from a bad fuse, relay to window motor, etc.:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Windshield_Windows_Window_Does_Not_Roll_Up_Down.htm

This should help narrow down your particular cause.
Brad

May 28, 2009 | 2000 Chevrolet Silverado

2 Answers

Installing new power window motor on a 1980 Corvette. Having some problems. Where does the window regulator need be for you install new motor? all the way up,down,middle etc. Need some tips not working...


You will need to roll the window down approx half way and you can either feel with your finger or get a small mirror to place in the door. You are looking for a hole in the regulator gear that will align with a hole in the main section of the regulator that bolts to the door. Once these are aligned you need to install a bolt through them and tighten it down. This will keep the regulator from moving when you remove the motor. Do not skip this step! If you remove the motor without this step you hurt yourself or even put a hole through your door. After you have the bolt in place you can remove the three bolts that hold the motor to the regulator.

May 06, 2009 | 1980 Chevrolet Corvette

1 Answer

1999 toyota vienta drivers side rear electric window not working


You need to replace the window regulator assembly.
The cables that run the glass up and down have broken inside the regulator.

Hope this helps. A FixYa rating would be greatly apprecited.

Jan 21, 2009 | 1995 Toyota Camry

1 Answer

Loose window on 1987 cutlass


replace all the felt liners on the window track ,and the inner ,outer seals at the top of door where the glass comes up thru,but also ck' the window regulator attachment to the glass at bottom...kev-mn.

Dec 10, 2008 | 1987 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...