Question about 2002 Mazda Protege

1 Answer

How to adjust idle speed w/AC on so the vehecile will not cut off or idle to fast w/AC off?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,016 Answers

Hi,

Ok you need to set the idle speed to 650 - 750rpm you can use the rev counter on the dash or get a Multimeter which has this function on it.

This is done by screwing the idle up screw on the side of the idle controller which is attached to the throttle body.

When the A/C is switched on this should go up too 700 - 800rpm.
If this is not happening then you have a idle up problem which is caused from your Idle controller on the throttle body.

You will need to get it checked/replaced.

Hop
e this helps, let me know if you need more information.

Thanks

Jason


Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

5.8 idle speed adjustment


In the past, adjusting an engine idle was easy. Manufactures have removed these adjustments on modern vehicles. The power control module or PCM now determines the speed at which an engine idles. The idle is controlled by the Idle air control. Remove and clean it out, it may be sticking, and making a fast idle. but if not done correctly, it can result in even worse idle issues. You can clean it with throttle body cleaner. Clean all the carbon from it, do not push on the pintle if it has one. Hope this helps you! God-Bless!

May 08, 2017 | Cars & Trucks

1 Answer

Correct fast idle


Check this link for fast idle adjustment.

Edelbrock Carburetors Troubleshooting Fast Idle Adjustment

Also check out the following link for details about the adjustment:

Pages 22 23 Choke Fast Idle Speed

Feb 12, 2015 | Cars & Trucks

1 Answer

I have a 2008 Chrysler 300. It runs great but sometimes the engine cuts off while idling when AC is on. What could be the problem?


fast idle a/c selenoid not functioning correctly. Should raise the idle speed when a/c is on. Replace or adjust it.

Jul 27, 2014 | Cars & Trucks

1 Answer

Engine idling


has adjustment on ac/solenoid on injector base

Mar 19, 2014 | 2005 Tata Indigo

1 Answer

I have a 1986 GMC 1500 with a 5.0 and stock rochester carb. The truck will start but you must keep gassing it as it won't idle. It kicks off every time. Any suggestions on how to fix this cold natured


fast idle speed screw, works off the fast idle cam which the choke adjustment sets, it works together by linkages. This is the raised idle speed setting you need to keep a cold engine running. First you set the idle speed by the idle speed screw with engine at normal operating temperature. Then you set the linkage up so the cam is on a raised step, throttle will be held on that raised step. then you can turn the idle speed screw to get idle at about 1500-1800 rpm. Now when you start engine cold, choke will set the fast idle cam on that raised step- when engine starts and runs it should be running at your fast idle setting. That's how it supposed to work, you just have to get everything adjusted right. I hate carburetors, they never stay adjusted right. Considering their complexity and small mechanical parts, no wonder.

Dec 24, 2013 | 1986 GMC C1500

1 Answer

Fast idle


The specification calls for 900 rpms for the idle speed when warm for the 1987 Dodge Shadow.

One can adjust this with a screw on the carburetor, if it has one.

If it's fuel injected the idle speed is automatically controlled.

Fast Idle Speed HOLLEY 5220/6520 Fig. 5: Turn the adjusting screw with a screwdriver to raise or lower the fast idle speed — make sure that the adjusting screw is resting against the lowest speed step 86735g04.gif
NOTE: This procedure is performed while the carburetor is installed on the engine.
  1. On 1981–82 cars, disengage the two-way electrical connector at the carburetor (red and tan wires).
  2. On all years, disconnect the jumper wire at the radiator fan and install a jumper wire so that the fan runs continuously.
  3. On 1983–86 models, pull the PCV valve out of the valve cover and allow it to draw underhood air.
  4. Disengage the oxygen sensor system connector located on the left fender shield near the shock tower.
  5. Ground the carburetor switch with a jumper wire.
  6. Open the throttle slightly and place the adjustment screw on the slowest speed step of the fast idle cam.
  7. With the choke fully open, adjust the fast idle speed to comply with the value indicated on the underhood sticker.
  8. Return the vehicle to curb idle, then reposition the adjusting screw on the slowest speed step of the fast idle cam to verify fast idle speed. Re-adjust as necessary.
  9. Turn the engine OFF, remove the jumper wire and reconnect the fan.
  10. Reinstall the PCV valve and remove the tachometer. On 1983–86 models, reattach the oxygen sensor system connector, and remove the jumper wire from the carburetor.
Fast Idle Opening MIKUNI
  1. Before adjustment, leave the carburetor alone for approximately one hour at 73°F (23°C).
  2. Adjust the fast idle opening by turning the fast idle adjusting screw to the following specified values (drill diameter):
    • 2.6L engines equipped with manual transaxles — 0.028 in.
    • 2.6L engines equipped with automatic transaxles — 0.031 in.
Choke Valve Setting MIKUNI Fig. 6: After tightening the choke cover lockscrews, cut the heads off of lockscrews A (total of 3 screws) and stake the heads of lockscrews B (total of 2 screws) with a blunt punch 86735g56.gif
NOTE: This procedure need only be performed if the carburetor is disassembled.
  1. Fit the strangler spring to the choke lever.
  2. Assemble the choke valve, aligning the inscribed line or black painted line on the tooth of the choke pinion with the inscribed line on the cam lever.
  3. Temporarily tighten the new lockscrews.
  4. Set the choke valve by moving the pinion arm up or down, align a punched mark on the float chamber cover at the center of the three inscribed lines, and secure the pinion arm with the lockscrews.
  5. Install the choke cover and tighten the lockscrews.
  6. Cut off the heads off of lockscrews A.
  7. Stake the heads of lockscrews B using a blunt punch.
Vacuum Kick HOLLEY 5220/6520 NOTE: This procedure is performed while the carburetor is installed on the engine. If the vacuum kick is adjusted to open the choke too far, the engine may stall or idle very roughly just after cold start. If it is adjusted so that the choke does not open enough, there may be black smoke in the exhaust. NOTE: To perform this procedure, you will need a hand held vacuum pump capable of producing at least 15 in. Hg (50.6 kPa) of vacuum. The vacuum kick diaphragm may be damaged if you attempt to retract it manually. You will also need a drill or dowel which has a diameter equivalent to the specification for Vacuum Kick in the Carburetor Specifications Chart.
  1. Remove the air cleaner. Open the throttle, close the choke and hold it in the closed position, and then release the throttle to trap the fast idle cam in the choke-closed position.
  2. Disconnect the vacuum hose at the choke vacuum kick diaphragm. Connect a vacuum pump and apply 15 in. Hg (50.6 kPa) or more of vacuum.
  3. Gently move the choke blade toward the closed position just until play is eliminated from the vacuum kick linkage (so that the vacuum kick is determining choke blade position).
  4. Insert the drill or dowel into the gap between the upper edge of the choke blade and the air horn wall, toward the center of the gap. The dowel or drill should just fit into the gap. If necessary, rotate the Allen head screw in the center of the diaphragm housing to create the proper gap and then recheck with the measuring device.
  5. Restore all vacuum connections and reinstall the air cleaner.

Aug 05, 2010 | 1987 Dodge Shadow

1 Answer

High idle CHevy 350 TBI


check if went from a V6 TO V8 need power two more cylinders

Jun 20, 2009 | 1992 Chevrolet K1500

2 Answers

Carberator


there is no idle speed adjustment its computer controlled if its ideling to fast there will be a vacume leak somewhere causing the engine to idle high.

May 24, 2008 | 2001 Ford Escape

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...