Question about 1999 Isuzu Rodeo

1 Answer

It is idilin to high i have adjusted the idil screw and the throttle cable is loose not tight so the cable

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Idling high could be either a throttle position sensor or a vacuum leak letting in too much air.

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Idiling high, temperature guage not working. no check engine light on. no problems shifting, fan coming off & on, blowing hot & cold air. can drive it, but it wont start up right away &


Check the cable to the temp sender unit is attached if so check the unit is working with a ohms meter. check the throttle cable is not binding ,the throttle leaver stop at the throttle body housing should be fully closed .

Mar 18, 2014 | 2005 Ford Escape XLT

1 Answer

How to adjust throttle cable on a 1989 Chevy 1500


is it idiling high?check the gasket under the throttle body.

Feb 10, 2010 | 1989 Chevrolet C1500

1 Answer

Throttle body cables are loose


is thr braket loose or just the cables. they should not be too tight, a little slack is ok,but if you step on gas pedal and throtle plate doesnt move then they are loose, some have an adjustment nut some dont,good luck,

Oct 04, 2009 | 1999 Dodge Ram

1 Answer

1986 subaru gl wagon non turbo stays idiling at 2500


Hate to tell you this but sounds like the problem is a vacuum leak. This will make the engine rev. Check all the vacuum lines before making any adjustment. Have to dig out some of my old books to find factory settings for that carb. Good luck and I will try to find in case you need them to restore carb settings.

Apr 13, 2009 | 1986 Subaru Gl 2 Door

2 Answers

My caprice runs to fast...


pretty sure that year is throttle body fuel injected if so check idle air control switch may be stuck or passage may need to be cleaned cylinder shape located on throttle body but first check all vacuum hoses for leaks or cracks

Mar 31, 2009 | 1985 Chevrolet Caprice

1 Answer

92 Dakota, trans doesn't slip, but stays in first a long time.


Possible throttle valve adjustment. Very critical. Cable is adjusted at throttle body. Too loose or too tight will have adverse effects. Recommend trans specialist perform adjustments

Mar 31, 2009 | 1993 Dodge Dakota

1 Answer

Idiling


yes you can and quite easily. on your throttle body there is a cable that runs to a metal thing that turns and that is your throttle cable. when you press the throttle it pulls the cable and makes the engine rev up. all you need to do is tighten up the nuts where the cable goes threw the metal and the rpms will go up. i suggest doing it while car is running

Nov 14, 2008 | 1995 Mazda MX-6

1 Answer

High Idle


The Throttle screw is located on the throttle (obiously) its in a clinderical shaped channel located on the throttle just oposite or obliquely opposite the the throttle body position sensor. In some mazda vehicles (IN TRINIDAD) you need to loosen the throttle body position sensor and slightle adjust it eighter to the right or left to tuen the idle (For electronic controlled axcelleration) in some cases it can be adjusted via an ODB2 diagnostic tool (only in some vehicles that has electronic controlled axcelleration)

You can tell what type your vehicle is by looking for an axcelleration cable connected to the throttle body. If the throttle body has a cable it isnt electronically controlled and has an idling screw. If there is no cable but wires to the position sensor its electronic.

Oct 31, 2008 | 1993 Mazda MX-3

1 Answer

Chyrsler sebring lxi 1995 2.5 v6 24 valve


ok this sounds easy when you ran the vehicle the computer controled the idiling motor now that you replace the idiling motor the computer hasnt been reset to except the new parameters
once you reset computer this should bring the idle back down to its specified idle
you can also adjust back of gas pedel the idle cable and on the throttle body by the idling screw

Jun 13, 2008 | 1995 Chrysler Sebring

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14394 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...