Question about 1993 Ford Tempo

Open Question

Install serpentine belt 1993 ford tempo

Need to put serpentine belt

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

Ad
  • 478 Answers

SOURCE: How to put a serpentine belt on a 2002 ford escort zx2

see diagram on hood or fan guard

Posted on Feb 11, 2010

  • 1 Answer

SOURCE: diagram on how to install ford focus 2006 zx4 serpentine belt?

I have replace alternators in my 2006 Ford Focus? Any one else had a problem with the alternator. My cd Player broke 3 times as well..and my car's key was stuck in the ignition and could not come out. i had to get that fixed..

Posted on Mar 11, 2010

  • 107 Answers

SOURCE: install a serpentine belt on 1994 ford tempo

under the hood should be a dieagram on proper install follow the pictures you will need a 3/8th or 1/2 in drive ratchet for the idler pully make shore to seat the belt in all the pullys good luck cj

Posted on May 14, 2010

  • 21 Answers

SOURCE: need 1993 plymouth voyager serpentine belt diagram

Which engine?
To replace the drive belt or serpentine belt on a Voyager check the engine size. For 2.4L engines, a serpentine belt runs the air conditioning compressor and alternator. For 3.0L models, the alternator and power steering share a belt with a separate belt for the AC. Dodge recommends checking the belts every 15,000 miles or 12 months for possible replacement. I have gone 3 yrs with one.. it will start squealing when you turn on the heater to defrost..

http://www.automd.com/46/how-to-replace-a-serpentine-belt/

Most replacement belts have a diagram on the package. However, the easiest way is to pay close attention to the belt you are taking off, and replace the new one the same way. The pulleys themselves are usually 'grooved' or 'smooth' which tells you whether the front or back of the belt is against it. The hardest part is figuring out how to release tension on the idler-pulley. If you can get the belt on and the idler/tension pulley (same thing) pulls the belt tight, chances are you got the belt right. If you don't know what I mean, then the mostest best way is to get a Clymer Manual and read up. Its really a simple thing to do yourself.

I used a long heavy duty screw driver to release the tension on a Pontiac Sunbird.. the belt will only fit on one way..

Posted on Jun 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 tempo drive belt installation


You use a special tool to move the belt tensioner to release tension on the belt. Sometimes you can use a regular wrench if you have enough room.
Make sure you have a diagram or draw one of the routing of the belt before you remove it so you know how to put the new one back on.

Oct 26, 2015 | 1994 Ford Tempo

1 Answer

The v belt wont turn on my 93 ford tempo


If the pulleys are turning, then how are they doing so without the belt turning them? Do you mean the pulleys are free and you can turn them by hand? If so then either the tensioner pulley isn't providing tension to the belt or the idler pulley has spun off and might be missing.

Nov 14, 2012 | 1993 Ford Tempo

1 Answer

I have a ford 1991 tempo,4 cylinder. There is a screeching coming from my car. When the screeching happends all the lights dim, and the air/heat blows out low, ones the screeching stop the lights go back...


The noise is most likely the drive belt. On that year and model, you have 3 different drive belts: one for the power steering, one for the alternator, and a serpentine belt for the rest of the accessories. Based upon your symptoms, the alternator belt would be suspect. But in this case, the alternator belt is a secondary belt powered off of the A/C pulley. So the culprit is most likely the serpentine belt. Cheapest solution is to replace the serpentine belt and see if that resolves the problem. If the problem persists, then the automatic belt tensioner for the serpentine belt is the next most likely culprit. This is a royal pain to replace and just the part can set you back in dollars. I've attached an exploded view of the right engine mount -- you will need to remove most of this in order to access the tensioner. Good luck with that!

_1010.jpg

Jan 02, 2011 | 1991 Ford Tempo 4 Door

1 Answer

Install a serpentine belt on 1994 ford tempo


under the hood should be a dieagram on proper install follow the pictures you will need a 3/8th or 1/2 in drive ratchet for the idler pully make shore to seat the belt in all the pullys good luck cj

May 14, 2010 | 1994 Ford Tempo

2 Answers

Ford tempo auto seat belts not working


You will need to replace the trac and motor. Try a salvage yard to save money.

Apr 03, 2010 | 1993 Ford Tempo

2 Answers

Change balt how to pull tensioner


serpentine belt tensioner tool is best because you have such a small amount of space between the tensioner and the vehicles body/frame.

Nov 04, 2009 | 1993 Ford Tempo

1 Answer

WHERE IS THE TENSIONER ADJUSTMENT FOR THE SERPENTINE BELT


if its a true serp belt/tensioner its auto adjusting. If you want to take it off get a 3/8 in drive ratchet or breaker bar (BB is better) and pull it to either side (the direction needed is different depending on the engine) until it disengages the belt. If its not holding tight enough the spring in it is shot and it needs to be replaced. if you have a V-belt setup the adjustments are usually the alternator and power steering pump.

Oct 03, 2009 | 1993 Ford Tempo

Not finding what you are looking for?
1993 Ford Tempo Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...