Question about 1993 Ford Ranger SuperCab

2 Answers

Fuel pump on my 93 ford ranger will not run and the check engine light will not come on when you turn the key on. Just put a new fuel pump on the truck. Any ideas on where to go next???

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

If u took the bed off to change the fuel pump make sure u hook the ground back up to the frame the ground should be on the driver side behind the tank,u need to change the fuel pump relay when u change a fuel pump because it could be bad to cause the first pump to quit working. not the right amount of volts or to much volts,the relay is under the hood in the fuse box,

Posted on Jul 31, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Try looking for the "inertia fuel shutoff" reset button located on passenger side under the carpeting....

Posted on Oct 12, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 Ford Ranger 2.3L manual running fine. Engine suddenly bogged down and died. Engine turns over, but won't start. Acts like it is not getting fuel. When you turn key you can hear fuel pump prime.


Just because you can hear the pump run, doesn't mean it is supplying enough fuel to properly operate the injectors. You need to check the fuel pressure at the fuel rail. If you have at least 45# of fuel pressure at the rail, you need to make sure that the injectors are metering. If memory serves me, I believe they are fired by the pickup in the distributor, but 93 is right when they were phasing into DIS ignition.

May 31, 2018 | Ford Cars & Trucks

1 Answer

Will the anti theft stop a 2001 ford ranger from getting fire to fuel pump


Have you checked the fuel pump cutoff switch? Do that first, make sure the red button is seated into the switch, if it is tripped it will click when you push the switch. Also you're aware the pump only runs when the key is held to the engine crank position and of course when the engine is running, with the key just turned on the pump will not have power.

Dec 06, 2016 | Ford Cars & Trucks

1 Answer

I have a 93 Ford F150 4.9 liter. And when I go to start it the fuel pump stays running for close to four minutes and then it will not start until the fuel pump shuts off?


OK, when you turn the key to on, it will start the pump for about 2 seconds-this is just to put pressure in the lines and in the fuel rail for easy starting. If key is not turned to start, pump will shut off after 2 seconds. But when cranking in start, and when engine is running, the pump is on full time.
If your pump runs longer than 2 seconds with key only in on position, you have a fuel circuit problem. It very well could be a bad fuel pump relay staying on. Or it could be a computer problem signaling the relay to stay on longer. Try a new fuel pump relay first and see if that was the problem.

Oct 07, 2016 | 1993 Ford F150 SuperCab

1 Answer

Starting problem


Change fuel filter. Check fuel pump in tank.

Feb 14, 2014 | Cars & Trucks

1 Answer

I have an 86 ford ranger 4x4 with a 2.9 v6 my problem started when i went to the store came out and my fuel pump wouldnt work after i turned the key on and off a few times it worked now when i went down to...


Check your battery, especially if it is older. Had same problem with 2007 Ranger.
It seems that there may be enough power in the battery to turn on daytime running lights, instrument cluster etc., and turn the engine over, but during all that, there may not be enough power left to adequately power the fuel pump.
After replacing a 9 year old battery, I had no more problems with my fuel pump (almost 1 year since battery was changed and no fuel pump issues).

Oct 09, 2017 | Ford Ranger Cars & Trucks

1 Answer

How to replace ford explorer fuel pump 1994


REMOVAL & INSTALLATION NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it. To install:
  6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up 89685g02.gif
    Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up 89685g03.gif
    Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer 89685g04.gif

  7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  8. Install the tank in the vehicle.
  9. Install a minimum of 10 gallons of fuel and check for leaks.
  10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  11. Remove the pressure gauge. Start the engine and check for fuel leaks.
prev.gif next.gif

Jul 31, 2010 | 1994 Ford Explorer Limited

1 Answer

NEED TO REPLACE FUEL PUMP FOR 1996 fORD eXPLORER, V6 4.0. WHERE IS IT AND HOW DO I GET TO IT?


Great SUV, I have the same model; for Ford Ranger/Explorer/Mountaineer 1991-1999 check this procedure to Fuel Pump - REMOVAL & INSTALLATION...
(see Figures 1, 2 and 3)

To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it.
To install:
  1. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
ab80e6f.jpg

Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up

fe10412.jpg

Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up

2bf46c6.jpg

Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer
  1. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  2. Install the tank in the vehicle.
  3. Install a minimum of 10 gallons of fuel and check for leaks.
  4. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  5. Remove the pressure gauge. Start the engine and check for fuel leaks.

Hope help with this; remember comment and rated this help. TY for using Fixya.

May 28, 2010 | 1996 Ford Explorer

1 Answer

3.0 6cyl 01 ranger - cranks but will not start. checked one of the plugs for spark and was okay. depressed schrader valve on fuel supply line while cranking engine and no gas came out. I believe the fuel...


check the fuel filter to see it that is plugged up. When turning the ignition key to on only without trying to start the engine you can hear the fuel pump running for a few seconds if working. If not the pump is bad

Feb 13, 2010 | 2001 Ford Ranger Regular Cab

3 Answers

1992 ford ranger 3.0


i was once pulling a trailer with a ranger when it suddenly lost power and the engine died. turns out the problem was with the fuel shut off inertia switch. the switch is supposed to activate in case of accident. on my model the inertia switch is located in the passenger side under the glove box. dont know where yours is located. once you find it, just push the button and see if it resets. good luck.

Sep 13, 2008 | 1992 Ford Ranger

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...