Question about Hyundai XG350

1 Answer

BELIEVE THAT INSTALLATION IS NOT ONLY AT TERMINALS BUT ALSO LOWER

Posted by on

Ad

1 Answer

What are trying to install?

Posted on Jul 31, 2010

  • transuer Jul 31, 2010

    MY QUESTION WAS: I HAVE A 2004 HYUNDAI XL350. I WAS TOLD THAT TO INSTALL THE CAR BATTERY NOT ONLY DO YOU INSTALL AT THE TERMINALS BUT ALSO BELOW THE BATTERY ITSELF. IS THIS CORRECT?

  • Anonymous Jul 31, 2010

    No, You only install it on the top post. If the battery has side post and top post then you will need to only install on the two battery terminals

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter removal of a 1995 contour


Removal and Install procedure on 2.0L...
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove starter motor upper mounting bolts.
  4. Raise and support the vehicle.
  5. Remove the nuts on the starter terminals and remove the cables from the terminals.
  6. Remove the two starter lower retaining bolts and remove the starter.
To install:
  1. Place the starter into position and tighten the 2 lower retaining bolts to 15-20 ft. lbs (20-27 Nm).
  2. Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm).
  3. Lower the vehicle.
  4. Install and tighten the upper retaining bolt to 15-20 ft. lbs (20-27 Nm).
  5. Install the air intake resonators.
  6. Connect the negative battery cable.
Hope helps.

May 14, 2011 | Ford Contour Cars & Trucks

2 Answers

How do you replace a fuel pump in a 87 olds 88


You need to make sure you are almost empty on fuel because the tank can be heavy. 1.Disconnect battery terminals. 2.Disconnect filler neck. 3.Loosen the gas tank straps. 4.Lower the gas tank and remove all fuel lines and wires. 5.Remove fuel tank and remove the the clamp or ring that traps the fuel pump.You might need a screwdriver for this. 6.Remove the fuel pump and disconnect all wires.Installation is reverse of removal.

Oct 02, 2010 | 1987 Oldsmobile Delta 88

1 Answer

How to change the starter from my 1994 chevy camaro


REMOVAL & INSTALLATION 3.4L and 1993-95 5.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If necessary for access to the starter, disconnect the exhaust crossover pipe from the manifolds.
  4. Unfasten the two starter mounting bolts/screws and carefully lower the starter motor.


To install:

Before attaching the electrical connectors, tighten the inner nuts on the solenoid terminals. If the nuts are not tight, the solenoid cap could be damaged during installation of the leads. Tighten the inner nut of the "BAT" terminal to 80 inch lbs. (9 Nm).
  1. Fasten the electrical leads to the starter motor assembly. Tighten the solenoid switch "BAT" terminal outer nut to 80 inch lbs. (9 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
  2. Position the starter motor to the engine and install the retaining bolts/screws. Tighten to 35 ft. lbs. (47 Nm).
  3. Measure the starter pinion-to-flywheel clearance and add shims, if necessary.
  4. If removed, connect the exhaust crossover pipe to the manifolds.
  5. Carefully lower the vehicle, then connect the negative battery cable. Tighten the cable to 11 ft. lbs. (15 Nm).

Hope helps.

Sep 06, 2010 | 1994 Chevrolet Camaro

1 Answer

Where is the location of the starter on a 1999 bonneville se and is it hard to take off yourself?


REMOVAL & INSTALLATION
(see Figures 2, 3, 4, 5, 6 and 7)
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
b6fb00e.jpg

Fig. 2: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion

9183313.jpg

Fig. 3: Exploded view of the starter motor electrical connections
  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
343c68b.jpg

Fig. 4: The starter is attached to the engine with 2 mounting bolts (see arrows)

32e179d.jpg

Fig. 5: Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation

3534611.jpg

Fig. 6: Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle


Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.

0694abc.jpg

Fig. 7: Exploded view of the starter motor mounting - 1987-97 vehicles


To install:
Note the location of any shims so they may be replaced in the same positions upon installation.
  1. Place the starter in position, then install the starter-to-engine bolts and tighten to 32 ft. lbs. (43 Nm).
  2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
    1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
    2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).
  3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
  4. If removed, install the splash shield.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Hope helps (remember rated and comment his).

Aug 06, 2010 | 1999 Pontiac Bonneville

1 Answer

How to replace starter


Check this procedure for Starter - REMOVAL & INSTALLATION...

2.0L Engine

02f9598.jpg

Fig. 3: Remove the three starter mounting bolts

d4f8fd2.jpg

Fig. 4: Carefully lower the starter out of the vehicle
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove starter motor upper mounting bolts.
  4. Raise and support the vehicle.
  5. Remove the nuts on the starter terminals and remove the cables from the terminals.
  6. Remove the two starter lower retaining bolts and remove the starter.
To install:
  1. Place the starter into position and tighten the 2 lower retaining bolts to 15-20 ft. lbs (20-27 Nm).
  2. Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm).
  3. Lower the vehicle.
  4. Install and tighten the upper retaining bolt to 15-20 ft. lbs (20-27 Nm).
  5. Install the air intake resonators.
  6. Connect the negative battery cable.

2.5L Engine

6f17117.jpg

Fig. 5: Starter mounting-2.5L engine
  1. Disconnect the negative battery cable.
  2. Remove the engine air cleaner assembly.
  3. Remove the fuel feed and return lines from the support bracket located on the accelerator cable bracket, and remove the fuel line bracket.
  4. On vehicles equipped with a automatic transaxle, remove the gear selector and the gear shift cable bracket from the transaxle.
  5. Remove the air cleaner support bracket from the engine and transaxle mount.
  6. Remove the nuts on the starter terminals and remove the cables from the terminals.
  7. Remove the starter motor-to-transaxle case retaining bolt at the rear of the starter.
  8. Remove the two starter retaining bolts and carefully lift the starter from the transaxle case while disengaging the alignment pins.
To install:
  1. Position the starter onto the alignment pins and onto the transaxle case.
  2. Install the two starter retaining bolts and the rear retaining bolt and tighten them to 15-21 ft. lbs. (21-29 Nm).
  3. Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm).
  4. Install the air cleaner support bracket.
  5. If removed, install the gear shift selector and bracket.
  6. Install the fuel line bracket and install the fuel lines in the bracket.
  7. Install the air cleaner assembly.
  8. Connect the negative battery cable.

Hope helps (remember comment and rated this).

Jul 16, 2010 | 1998 Mercury Mystique

1 Answer

How do i get the instructions on how to replace a starter for an 1989 pontiac bonneville


REMOVAL & INSTALLATION
(see Figures 2, 3, 4, 5, 6 and 7)
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
a20ef19.jpg

Fig. 2: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion

6700461.jpg

Fig. 3: Exploded view of the starter motor electrical connections
  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
7369158.jpg

Fig. 4: The starter is attached to the engine with 2 mounting bolts (see arrows)

168c839.jpg

Fig. 5: Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation

3142660.jpg

Fig. 6: Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle

Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.

5e6998d.jpg

Fig. 7: Exploded view of the starter motor mounting - 1987-97 vehicles

To install:



Note the location of any shims so they may be replaced in the same positions upon installation.
  1. Place the starter in position, then install the starter-to-engine bolts and tighten to 32 ft. lbs. (43 Nm).
  2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
    1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
    2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).

  3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
  4. If removed, install the splash shield.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Hope helps (remember rated and comment this).

Jun 05, 2010 | 1989 Pontiac Bonneville

1 Answer

Where do I find the starter for my 1997 buick lasabre - I need to replace this part.


  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
9795685.gif
Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion

ea58721.gif
Exploded view of the starter motor electrical connections

  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
d3e4880.gif
The starter is attached to the engine with 2 mounting bolts (see arrows)

aa0a8cb.gif
Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation

d22a19d.gif
Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle

Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.

e5e4cd3.gif
Exploded view of the starter motor mounting - 1987-97 vehicles

To install:
Note the location of any shims so they may be replaced in the same positions upon installation.
  1. Place the starter in position, then install the starter-to-engine bolts and tighten to 1 ft. lbs. (43 Nm).
  2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
    1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
    2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).
  3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
  4. If removed, install the splash shield.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Oct 31, 2009 | Buick LeSabre Cars & Trucks

1 Answer

Where is the starter on a 2000 Mercury Cougar?


REMOVAL & INSTALLATION 2.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove starter motor upper mounting bolts.
  4. Raise and support the vehicle.
  5. Remove the nuts on the starter terminals and remove the cables from the terminals.
  6. Remove the two starter lower retaining bolts and remove the starter. To install:
  7. Place the starter into position and tighten the 2 lower retaining bolts to 15–20 ft. lbs (20–27 Nm).
  8. Place the starter cables onto the terminals and tighten the retaining nuts to 80–124 inch lbs. (5–7 Nm).
  9. Lower the vehicle.
  10. Install and tighten the upper retaining bolt to 15–20 ft. lbs (20–27 Nm).
  11. Install the air intake resonators.
  12. Connect the negative battery cable.

2.5L Engine

  1. Disconnect the negative battery cable.
  2. Remove the engine air cleaner assembly.
  3. Remove the fuel feed and return lines from the support bracket located on the accelerator cable bracket, and remove the fuel line bracket.
  4. On vehicles equipped with a automatic transaxle, remove the gear selector and the gear shift cable bracket from the transaxle.
  5. Remove the air cleaner support bracket from the engine and transaxle mount.
  6. Remove the nuts on the starter terminals and remove the cables from the terminals.
  7. Remove the starter motor-to-transaxle case retaining bolt at the rear of the starter.
  8. Remove the two starter retaining bolts and carefully lift the starter from the transaxle case while disengaging the alignment pins. To install:
  9. Position the starter onto the alignment pins and onto the transaxle case.
  10. Install the two starter retaining bolts and the rear retaining bolt and tighten them to 15–21 ft. lbs. (21–29 Nm).
  11. Place the starter cables onto the terminals and tighten the retaining nuts to 80–124 inch lbs. (5–7 Nm).
  12. Install the air cleaner support bracket.
  13. If removed, install the gear shift selector and bracket.
  14. Install the fuel line bracket and install the fuel lines in the bracket.
  15. Install the air cleaner assembly.
  16. Connect the negative battery cable.

Jun 24, 2009 | Mercury Cougar Cars & Trucks

1 Answer

Starter replacement


  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If necessary for access, remove the splash shield.
  4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
  5. Label and detach the electrical connectors from the starter.
89632p02.gif Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion
89632g34.gif Exploded view of the starter motor electrical connections
Click to Enlarge
  1. It may allow more room it you remove the right side cooling fan.
  2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.
89632p03.gif The starter is attached to the engine with 2 mounting bolts (see arrows)
89632p04.gif Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation
Click to Enlarge
89632p05.gif Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle
Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.
89632g33.gif

Oct 22, 2008 | 1994 Buick LeSabre

1 Answer

Oil pressure sender


It is located on the side of the oil pan, enclosed is a little more info on testing and installation.

TESTING
See Figure 1
  1. Unplug sensor connector and insert a jumper wire between terminals 1 and 2.
  2. Start the vehicle.
  3. If the light is on, check the harness and dashboard light.
  4. If the light is off, replace the sensor and recheck the light operation.
0900c1528008c49c.jpgFig. 1: Connect a jumper wire between terminals 1 and 2REMOVAL & INSTALLATION
See Figures 2, 3 and 4
  1. Raise and safely support the vehicle.
  2. Unplug the connector from the sensor.
  3. Unfasten the sensor mounting bolts and remove the sensor from the oil pan.
To install:
  1. Install the sensor into the oil pan.
  2. Tighten the sensor mounting bolts.
  3. Plug in the sensor connector.
  4. Lower the vehicle.
0900c1528008c49d.jpgFig. 2: The oil pressure sensor is mounted to the side of the oil pan-850 model shown 0900c1528008c49e.jpgFig. 3: Unplug the connector from the oil pressure sensor 0900c1528008c49f.jpgFig. 4: Unfasten the retaining bolts and remove the sensor

Oct 01, 2008 | 1990 Volvo 740

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...