Question about 1997 Toyota Camry

1 Answer

Can the rotors and calipers from a 1992 Camry be used on a 1997 Camry?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 14,036 Answers


Posted on Jul 31, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I eplace the front rotors on a 1997 Mitsubishi Montero Sport 4wd? Is there a special tool required to remove and replace the rotor and is there an adjustment needed inside the hub?

jack up the car, first break lugs, and remove tire. There are two bolts on the front back side, if it like are endeavor then I compressed the caliper piston and then I had to take apart the caliper as the old pads did not come out, those are the two bolts on each end. then put back on. Once the caliper is off the rotor will come off as it is held on by the caliper. Just be careful with the caliper once it is removed as it is a brake line, you can use a hanger for it does not pull on the line when it is off the rotor. Good Luck Tim

Oct 03, 2010 | 1997 Mitsubishi Montero Sport

1 Answer

1997 Toyota Camry, when coming to a stop i feel a slight movement in the brake pedal at the end, i have had the brakes checked and was told that the pads rotors, and calipers are fine, also the ABS light...

There is a possibility that the rotors are warped and need either turned or need new ones. If ABS is acting up it could effect the pedal movement too but usually more drastic movement. Only other way to know is have a good mechanic run the scanner checking brakes on the run.

Jul 10, 2010 | 1997 Toyota Camry

5 Answers

Why do my front rotors get worped so fast?

warped rotor happen for a couple of reasons,first is someone who rides there brakes down a hill instead of pulling it out of overdrive,second is someone who is used to riding their left foot on the brake pedal,third is coming to a quick stop and going to fast type driving.
if you've replaced the rotors you should know there are three types that are sold the lowest price rotors about $20.00 each are not the thinkness of your originals,then the price goes up to the mid grade,then there are the best which are original thickness,
the thinner the rotor the faster it will heat up and cool warped.

Jan 20, 2010 | 1992 Ford Explorer

2 Answers

Need diagram of brake caliper assembly for 2000 camry go here and scroll down until you see the front suspension diagram, it includes the brake assembly as well as a few other tidbits youu might wanna see....the diagram is good for 1997-2000 camery's

Sep 27, 2009 | 2000 Toyota Camry

1 Answer

92 Camry New rotor, brakes Rotor still getting torn up by brakes.

You need to check for any looseness in the wheel that this is occuring, since you haven't mentioned which one. Did you tighten the axle nut enough? Is the caliper brake not twisted so as to not tighten when turning. The calper bracket may be out of line.

Jun 21, 2009 | 1992 Toyota Camry V6

1 Answer

98 Camry brakes

I would suggest replacing the caliper hoses and following a proper bleeding procedure before replacing the master cylinder

Nov 02, 2008 | 1998 Toyota Camry

2 Answers

2004 Toyota Camry Brakes

Raise the vehicle up and remove the rims & tires

Remove the brake pads, and then remove the calipers from the caliper retention brackets, do NOT remove the brake hoses from the calipers.

Remove the caliper retaining brackets from the hub assemblies (2 large bolts on backside of the bracket)

Tap the brake rotors off of the hubs, hit them from the back side of the rotor.

No big mysteries here, this is a very easy job.

Oct 21, 2008 | 2004 Toyota Camry

1 Answer


if you are only replacing pads and the rotor you should not need to open the bleeders. they are located on the calipers. all you have to do to back off the piston of the caliper is to use a small C-clamp. you place the stationary part on the back of caliper and the screw part on the piston of caliper. turn the screw until the piston moves back into the caliper housing this should allow you to put the new pads on and fit the caliper over the rotor. hope this helps. please rate this solution. thanks

Aug 30, 2008 | 1992 Ford Crown Victoria

Not finding what you are looking for?
1997 Toyota Camry Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides