Question about Ford Explorer

1 Answer

P1400 code came up voltage low.I want to know what its suppoded to have

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

The d p f sensor is bad,,this is called the e g r valve position sensor also,replace it,and the hoses going to it,these are special hoses,look for them at napa,they will have them in stock.If this was at all helpful,please rate,thank you.

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford expedition check engine light is on. It is reading a p405 code which is the egr sensor. I have change the sensor and the pig or electrical code twice . I brought the sensor from ford.


This DTC says nothing about changing the sensor or the connector or pig tail ! It's a circuit voltage low code
P0405 - DPF EGR Sensor Circuit Low Voltage Detected See DTC P1400 Problem with wiring or PCM !
P1400 - DPF EGR Sensor Circuit Low Voltage Detected The EGR monitor checks the DPF EGR sensor signal to the PCM for low voltage. The test fails when the average voltage to the PCM drops to a voltage less than the minimum calibrated value.
  • DPFEGR circuit short to GND
  • Damaged DPF EGR sensor
  • VREF short to GND
  • Damaged PCM
A DPF EGR PID reading less than 0.2 volt with the key ON and engine OFF or running, indicates a hard fault.

Sep 01, 2016 | 2003 Ford Expedition

2 Answers

Code p1400 gmc enjoy 2007 what is the problem in this code


Definition of Diagnostic Trouble Code P1400 Audi: EGR Valve Circ Electrical Malfunction BMW: Heated Catalyst Battery Voltage or Current too Low during Heating (Bank 1) Chrysler: Manifold Differential Pressure Sensor Circuit Malfunction Dodge: Manifold Differential Pressure Sensor Circuit Malfunction Ford: Differential Pressure Feedback EGR Circuit Low Input Hyundai: EGR System Monitor Malfunction Infiniti: EGRC Solenoid/V Jaguar: Exhaust Gas Recirculation Valve Position Control Jeep: Manifold Differential Pressure Sensor Circuit Malfunction Lexus: Sub-TPS Malfunction Lincoln: Differential Pressure Feedback EGR Circuit Low Input Mazda: DPFE Sensor Circuit Low Input Mercedes: EGR Switchover Valve Malfunction (C230 Only) Mercury: Differential Pressure Feedback EGR Circuit Low Input Mitsubishi: Manifold Differential Pressure Sensor Circuit Malfunction Nissan: Differential Pressure Feedback EGR Circuit Low Input Subaru: Fuel Tank Pressure Control Solenoid Circuit Low Input Toyota: Sub-Throttle Position Sensor Malfunction Volkswagen: EGR Valve Circ Electrical Malfunction

Jun 20, 2015 | 2007 GMC Envoy Denali

1 Answer

Can you tell me the answer for code P1400 for 2007 Trailblazer


P1400 - Heated Catalyst Battery Voltage or Current too Low During Heating (Bank 1)

Jun 08, 2012 | 2007 Chevrolet Trailblazer

3 Answers

My 2002 Ford Explorer gave me code P1400. What does it mean


P1400 indicates the following:
Differential Pressure Feedback Electronic Sensor circuit Low Voltage

Most common cause is a bad DPFE sensor.

Jul 15, 2011 | 2002 Ford Explorer

1 Answer

Either code 4000 or 1400 on 2002 ford ranger 4.0 ltr v6. the right code should equate to the egr valve. I have replaced the egr valve but check engine light comes on again after reset showing same code.


code p1400 is a DPF EGR sensor CIRCUIT LOW VOLTAGE detected. most likely is a problem with the wiring to the egr or dpfe sensor. the pinpoint tests for code p1400 instruct you to test all wiring before replaceing the egr or dpfe sensor

Jan 19, 2011 | 2002 Ford Ranger Regular Cab

3 Answers

Ford Taurus. Check Engine Light Code P1400


P1400 Exhaust Gas Recirculation valve position sensor
P1401 Exhaust Gas Recirculation valve position sensor
P1402 Exhaust Gas Recirculation metering orifice restricted
P1403 Exhaust Gas Recirculation differential pressure sensor
P1404 EGR Temperature Sensor circuit
P1405 Exhaust Gas Recirculation Differential Pressure Feedback Sensor upstream hose off or plugged
P1406 Exhaust Gas Recirculation Differential Pressure Feedback Sensor downstream hose off or plugged
P1407 EGR solenoid -No Flow Detected
P1408 EGR solenoid -Flow out of Self- Test Range
P1409 EGR Vacuum Regulator solenoid circuit malfunction
---
The sensor for the EGR Valve position is not functioning correctly.

Oct 16, 2010 | 2002 Ford Taurus

1 Answer

Get a p1400 code check engine light


P1400 - DPFE (Differential Pressure Feedback Electronic) Sensor circuit Low Voltage

The DPFE sensor is usually not hard to change. There are 2 small rubber hoses that run from the EGR tube to it...

17570fe.gif

Replace DPFE sensor, reset engine fault codes. The Ford one is a good one and rockauto.com carries Airtex. Sometimes I hear that this change always need replace EGR valve to delet all codes. Test it.

Good luck.

Jul 07, 2010 | 2002 Ford Explorer Sport Trac

3 Answers

Wat does code p1400 means


In order to give you accurate information. I need size of engine example 2.0 L 3.0L. but code P1400 means Differential Pressure feedback EGR circuit low input. Maybe your differential oil is low.

Apr 01, 2010 | 2002 Ford Taurus

1 Answer

I have a ford ranger and the diagnostic code coming up is p1400 evg low voltage...ranger is 1998...


Ok.. The code P1400. Is. Related with the E.G.R system.
" Exaust Gas Recirculation"
The code P1400 is Exactly.
Sensor DPFEGR low voltage.
This code can set for.
Leaking up-strim pressure hose.
DPFEGR sensor Short to ground or signal return circuit.
VREF selenoid shorted to ground or signal return circuit.
Faulty DPFEGR .
or In the last case faulty PCM.

Ok.. The DPFEGR is a little box Located at the intake manifold.
to identificate See the Exaust Manifold Gasket you will see.
2 Little hoses Goin at the little box. When you found.
Check the hoses for cracked or damaged repair as need.
Check the connector.
The VREF. to locate follow the Little vaccum hose GREEN.
Goin to the EGR attached at the Intake manifold .
and check the connection.
If everything is OK. I recomend to replace the DPFEGR.

NOTE. If you don't have enought Expertise on vehicles.
I recomed to consult with your mechanic. and maybe give this information.
But if you can do your self go ahead.

I hope this help on your question. THANK YOU FOR USE FIXYA..

Dec 01, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Engine light on 2002 Explorer. engine code P1400


This may have to do with a bad wiring. Check all the wiring associated with EGR operation. Whenever a computer throws a code about high or low circuit voltage, it is usually attributed to abnormal wiring.

Nov 14, 2009 | 2002 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...