Question about 2003 Ford E150

1 Answer

Where is cylinder 8 located? - 2003 Ford E150

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Back cylinder on the drivers side.

Posted on Jul 31, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to knock sensor location

you didn't state specific engine so here is a run down of locations
on a 4 cylinder engine there are 2 knock sensors located on the inlet side of the block adjacent to no 1 and 4 cylinders ( cross way motor)
on a v6 engine( crossway engine) they are in the valley of the block ( probably under the inlet manifold system) at 2 and 5 cylinder positions
on a v8 they will be located adjacent to 4 cylinder and between 6 and 8 cylinder on one side and adjacent to 3 cylinder and between 5 and 7 cylinder on the other side

Nov 22, 2014 | 2000 Toyota Land Cruiser

1 Answer

Ignition coil location number 1

the number one cylinder is the front cylinder on the passenger side. Those cylinders are 1-2-3-4

the drivers side cylinders are 5-6-7-8

I’m happy to assist further over the phone at

Feb 14, 2012 | 1999 Ford Expedition

1 Answer

Fireing order and cylinder location on a 1999ford f150 4.6 l v 8 triton


Right hand side cylinders go as: (as you are sitting in the truck)
left hand:

5 Front of engine 1
6 2
7 3
8 4

hope this helps

Aug 29, 2011 | Ford F-150 Cars & Trucks

1 Answer

I have a f150 2000 5.4 liter 4wd, i need to locate #8 cylinder, the engine light came on and i had it checked and that cylinder misfired. please help me if you can. thank you

as you look at the vehicle from the front left bank is usually right bank is rear plug is #8 cylinder you can also follow the wires from the distributor, or from the coil pack to locate the cylinder you are looking for

Jun 12, 2011 | 1984 Ford F 150

1 Answer

Which cylinder is the number 8 cylinder

Looking at your engine from the front of the vehicle the #8 cylinder is the last cylinder on the right, or drivers side.

Front of Vehicle (Cyllinder Locations)
Drivers side Passenger side

5 1
6 2
7 3
8 4

Nov 20, 2010 | 2000 Ford Crown Victoria

1 Answer

Where is the location of no. of cylinder on crown

2004 Ford Crown Victoria 4.6 liter V-8 VIN "W"


Hope helps (remember rated this).

Jul 19, 2010 | 1997 Ford Crown Victoria

1 Answer

I am looking for the cylinder head torque specification for the 3.3litre chrysler town and country 2003

Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values:
Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
NOTE: Bolt torque after 1/4 turn should be over 122 N·m (90 ft. lbs.) If not, replace the bolt.

Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N·m (25 ft. lbs.) after head bolts 1 - 8 have been tighten to specifications.

Jan 24, 2010 | 2003 Chrysler Town & Country

2 Answers

Where is the number 8 piston on a 1998 grand

Hello mrmrsg_520: My name is Roger and I will help you. Number 8 cylinder is located at the rear of the left cylinder head. See the attached picture. Should you need further help please just ask. Please rate the quality of the answer. Thank You for using Fix Ya.Roger9df1b6f.jpg

Nov 09, 2009 | 1992 Mercury Grand Marquis

2 Answers

Where is the intake valve located on a 1988 GMC Jimmy Blazer - I dont even know what one looks like - sorry some girls just dont know that much about cars/truck - but I am trying to learn.

the intake valves are deep inside the engine, it is part of what is called a cylinder head, there is one valve (some engines have 2) for each cylinder of the engine, a V6 has 6, a V8 has 8, what is the problem?

Apr 30, 2009 | 1998 GMC Jimmy

2 Answers

Location of cylinder 4

here is the cylinder layout diagram for thios engine.

Apr 15, 2009 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides