Question about 2000 Chevrolet Venture

1 Answer

Front wiper blades stay in up position...started after i had battery replaced. any advice

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 76,846 Answers

Try disconnecting the battery NEGATIVE cable for 5 minutes to reset Body Control Module. This often fixes the problem.

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i stop the wiper blades in the middle of the screen jaguar xj


On the WEB:

Front Wiper Blade Change Jaguar XJ8 (2004-2009) - 2008 ...

www.carcarekiosk.com/...Jaguar.../windshield_wiper_blade.../replace_wi...
Free video on how to replace the front windshield wiper blades in a 2008 Jaguar XJ8 L 4.2L V8. Complete instructions for changing the front wiper windshield ...

Jul 25, 2015 | Jaguar Cars & Trucks

Tip

Replacing Wiper Blades or Not


Do not replace your wiper blades until you have tried this, get some warm soapy water, soft all purpose cloth. Hose down your front and rear windscreen (if fitted with wiper blades) with normal water, clean the windscreen as you would when washing the vehicle. Get your cloth and dip it into warm soapy water, if your wiper arm stays upright put it in that position other wise lift it up and put a piece of towel or similar under it. Now with the soapy cloth give the wiper blade edge a good scrub, up and down, hold the blade itself with one hand on one end, it may slide out, you will notice the cloth getting black, you are cleaning off all the dirt that is stuck on the wiper blade, simple as that. It is usually that dirt which causes your wiper blades not to clean properly, you will eventually need to replace it but give it a go, you will be surprised.

on Feb 20, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

I need to have 'step-by-step' instructions for replacing the driver side windshield wiper arm on my 2000 Ford Explorer. Can you help me with this?


  • Turn your wipers off, using the stalk on the left side of your steering column. Turn your ignition off and remove the key.

  • 2

    Pull the wiper blade up to lift it to the service position. Pull the front part of the blade down to position it at an angle.

  • 3

    Pull back the lock pin on the center part of the wiper blade (where it connects to the wiper arm). This unlocks the blade from the wiper arm.

  • 4

    Grasp the blade on each side and pull it down (away from the extended wiper arm) to release it from the "U" clip.

  • 5

    Repeat the process for the other wiper blade, if desired. Removing the driver's side and passenger's side wiper blade is the same.

  • 6

    Install the new wiper blade. Open the lock pin on the new blade, and then insert it into the wiper arm "U" clip. Close the lock pin and lower the wiper blade to its normal position.

  • Jan 29, 2011 | Ford Explorer Cars & Trucks

    1 Answer

    I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


    Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
    1. Turn ignition switch to ACCY position.
    2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
    3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
    To Install:
    1. Insert wiper arm hook through opening in wiper blade.
    2. Place wiper blade pivot in the inside radius of wiper arm hook.
    3. Pull on wiper blade pivot into hook until it locks into place.
    4. Check wipers for proper operation.
    Wiper Arm To Remove:
    NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
    1. Remove washer hose.
    2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
    3. Remove wiper arm from shaft.
    To Install:
    1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
    2. Press arm assembly on shaft and push retaining latch IN.
    3. Connect washer hose.
    4. Remove windshield markings and check wipers for proper operation.
    prev.gif next.gif

    Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

    1 Answer

    We're replacing the motor, gear box and plates to


    The wiper linkage and blades should be in the neutral position, or where they would normally lie when in the "off" position. Hope this helps. Remember to disconnect the battery while replacing electrical components.

    May 12, 2010 | 1999 Chevrolet Venture

    1 Answer

    Removing front wiper blade 1998 gr cherokee


    The center of the wiper blade has a tab that must be pushed and held in as you remove the blade assembly

    Mar 27, 2010 | 1998 Jeep Grand Cherokee

    1 Answer

    I cant figure out how to change my windshield wiper blades on 2001 ford ranger


    How to Replace Wiper Blades Guide (Typical):
    Potential tools needed to replace wiper blades:
    • Flat blade screwdriver (small)
    • Small nosed pliers
    • Latex or vinyl gloves
    • Safety goggles
    To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
    • Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
    • Step 2: Locate the mounting clips at the top pivot on the wiper blade
    • Step 3: Release the clip and remove the wiper arm
    • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
    • Step 5: Reinstall the new wiper blade and recheck wiper operation

    Common Problems:
    • Make sure the wiper blades are the same size as the original blades.
    • When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
    • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
    • Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

    I hope help you with this (remember rated this help) Good luck.

    Sep 16, 2009 | 2001 Ford Ranger Regular Cab

    2 Answers

    How do I remove front wiper blades to replace with new ones on my 2006 nissan quest


    How to Replace Wiper Blades Guide:
    Potential tools needed to replace wiper blades:
    • Flat blade screwdriver (small)
    • Small nosed pliers
    • Latex or vinyl gloves
    • Safety goggles
    To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
    • Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
    • Step 2: Locate the mounting clips at the top pivot on the wiper blade
    • Step 3: Release the clip and remove the wiper arm
    • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
    • Step 5: Reinstall the new wiper blade and recheck wiper operation

    Common Problems:
    • Make sure the wiper blades are the same size as the original blades.
    • When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
    • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
    • Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

    I hope help you with this (remember rated this help) Good luck.

    Sep 14, 2009 | 2006 Nissan Quest

    1 Answer

    How to replace the wiper insert at the back of


    moz-screenshot.jpg
    1. REMOVE RR WIPER BLADE
      1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
      2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

    1. REMOVE REAR WIPER RUBBER
      1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
    f54b10a.gif
    1. INSTALL REAR WIPER RUBBER
      1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
    0dd144d.gif
    b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
    8f40009.gif
    c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

    Sep 12, 2009 | 2005 Toyota Matrix

    1 Answer

    How do i time my wiper blades after replacing wiper motor blades stay in vertical position when set on interrmitent


    Remove the wiper arms from the drive posts. Turn on your wipers with the engine running and shut the wipers off -- this will put the wiper drive posts in the park position.

    Reinstall the wiper arms so the blades are about an inch above the bottom of the windshield.

    Charlie

    Aug 22, 2009 | 2001 Chevrolet Monte Carlo

    Not finding what you are looking for?
    2000 Chevrolet Venture Logo

    126 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...