Question about 1997 Mitsubishi Diamante

Open Question

How do I replace door mirror on my 97 daimante (drivers side). I have the old mirror (It some how popped out) and surrondding shell. I need to get it clipped back in so the power works on it.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 548 Answers

SOURCE: i need to replace passenger side mirror on 97 ford expedition

You probably don't need to pull the door panel. On the outside of the mirror is a plastic trim cover. Use a trim stick to remove it to allow access to the screws holding the mirror in. Don't unhook them yet. On the inside, remove the plastic trim over the door/windshield pillar - first removing any grab handles that may be there. You don't say if this is a power mirror. If not, then that should do it. If it is, you may need to lift the dash cover up slightly with the trim stick to gain access to any electrical hookups.

Trim stick = soft tool for use in removing plastic pieces without messing them up.

Posted on Dec 27, 2008

Ad
  • 1861 Answers

SOURCE: Replace 97 Camry passenger side mirror

If you pull off the triangular black plastic trim behind the mirror, you will see the mirror wiring. If there is no plug, you will have to pull off the door panle. .....SOME Japanese cars have the plugs, but not all of them...Americian built cars do not. They are different.

Posted on Feb 09, 2009

  • 60 Answers

SOURCE: Passenger side mirror replacement procedures

If its a power mirror there is more thing you will have to remove to get to the wires but if not there is a screw on the corner piece on the inside of the door. just pull the screw out and the bolts (3) that hold the mirror on are behind it. If it power then you will have to remove the door panel to access the wiring to disconnect it

Posted on Jun 21, 2009

  • 1986 Answers

SOURCE: passenger side door mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 563 Answers

SOURCE: 97 mitsubshi daimante gdi. Lack of power up hill.

You could handle a do-it-yourself-tune-up....
Get the Hanyes manual, and follow tune-up procedures.
Replace the spark-plugs, change engine-oil/filter, air-filter, service the injector body, change coolant/thermostat

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace my audi a6 driver side mirror? I have the new one and i'm trying to take off the old one, but i don't want to damage anything. How do i remove the old one?


Hi,to remove it the door panel needs to come of and then the cover on in side of door at side of mirror there will be screws there for the mirror.hope this helps

Jul 20, 2011 | 2004 Audi A4

1 Answer

I've got a broken driver side rear view mirror on a 1990 Buick Century. I've got the replacement mirror, I just need help getting the old mirror off the door. Suggestions?


This is what you do take the door skin off of the inside of the door and at the top corner there will be i think three nuts and than your going to need door clips after your done in order to put the door panal back on

Apr 07, 2010 | 1990 Buick Century

1 Answer

My driver side heated mirror on my 2002 jeep liberty limited was sideswiped. How do I go about replacing it with a new one? I am hoping to find step-by-step instructions.


1.call the chrysler dealership for a new replacement or call around to autowreckers for one. 2.open the door. 3.pry off plastic from door to mirror spindle. 4.check wiring coloring. 5. pull off plastic under steering wheel may be held on by 2 or 3 screws. 6.locate wiring from mirror under dash. 7.unplug wiring harness for mirror. 8.pull out old wiring. 9.remove old mirror with old wiring harness. 10. replace with new mirror and wiring harness and then repeat.

Jan 05, 2010 | 2002 Jeep Liberty

2 Answers

97 mitsubshi daimante gdi. Lack of power up hill.


Sounds like its time for a tune up. Start there and your mechanic will be able to note any other abnormal conditions. change fuel/air filter and any other maintenance items you haven't done so far.

Nov 05, 2009 | 1997 Mitsubishi Diamante

1 Answer

I need to know how to replace Power Mirror on '97 Thunderbird LX


Yes, you may have to take off the inside door trim.

B

Sep 09, 2009 | 2005 Ford Focus

1 Answer

How to replace the driver side mirror on Camry 96


if just the mirror pop it in. use a little grease on the slots so it slips in. if replacing whole mirror assembly take off the small triangular plastic inside the door. pull from top edge it should pop out. take off 3 nuts. if the plug for the mirror is inside the door panel then you have to remove the whole door panel.

Jun 24, 2009 | 2002 Toyota Camry

1 Answer

Passenger side mirror replacement procedures


If its a power mirror there is more thing you will have to remove to get to the wires but if not there is a screw on the corner piece on the inside of the door. just pull the screw out and the bolts (3) that hold the mirror on are behind it. If it power then you will have to remove the door panel to access the wiring to disconnect it

Jun 21, 2009 | Ford Taurus Cars & Trucks

1 Answer

R&R mirror itself on Driver's side door


On the Back of the mirror in the middle is a big plastic ring that is a pressure fitting you should be able to just pop the old one out and put the new one in. If you have to replace the whole assembly it's easy if you look at the inside of the door rigth where the mirror is attached there is a triangle piece of plastic you can just pop that off and there will be three bolts in side to remove the mirror if you have there should be some foam protecting the electrical wires inside that just comes out. Good Luck.

Jun 15, 2009 | 2001 GMC Sierra Crew Cab

1 Answer

Replacing passenger side-view mirror on 1999 Dodge Stratus


Watched my dad do it this afternoon. There is an exposed screw on the left side of the door panel and one at the bottom of the panel. There are also two hidden screws, one behind the door handle and one inside the little hole in the armrest (pop off the plastic plugs). There are also three recessed screws behind the speaker cover. You can pop the speaker cover off with a flathead screwdriver. I'm pretty sure thats all of them. You can pop the panel off then, but watch the wires connecting stuff inside. The hardest part is getting it over the door lock. .

Once the panel is loose you have to pop off the black plastic cover hiding the back of the mirror. There are three recessed bolts holding the mirror. My dad had to get a special wrench to get those off and he dropped one inside the door, so be careful (we fastened a magnet to a coat hanger and got it back). Mine had some remote gizmos, so he had to had to unplug the little square thing and then popped off what was left of the old mirror. If your new mirror has a wire with a little box, feed it through the hole and plug it in. Once you have it positioned correctly, you can screw on the bolts and put eveything back together. It helps to have another person there while you are trying to position the mirror correctly. Hope I didn't miss anything. Good luck!

Apr 19, 2009 | 1999 Dodge Stratus

1 Answer

Removing/installing door components from/to door shell


sorry i cant tell u how to exactly howto take the old door apart NICELY without just having a light touch and the experience of doing other doors, but i would like to ask where u got ur door shell, i need one badly myself to and have had no luck so far finding one. any knowlage u have would be awsome, thanks

Mar 24, 2009 | 2003 Toyota Corolla

Not finding what you are looking for?
1997 Mitsubishi Diamante Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

81424 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...