Question about 1998 Plymouth Grand Voyager

1 Answer

How do you remove the head ligh assembly? We want to replace them Thanks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,509 Answers

Four 10MM headed bolts that screw in to the back of them though the raditior support, it's close so you might have to remove things in the way to get to the bolts. look at your new ones and you can see where the bolts are.

Posted on Jul 30, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i replace headlight globes on mr2 sw20?

Turn headlights to on. Then 2 clicks back to turns lighs off but keep headlights up/open.

Remove headlight shrouds, (Black plastics.) Use phillips + head screw driver.

Remove chrome trim ring using phillips head screw driver.

Pull out headlight bulb. Disconnect from harness.

Reverse to install.

Sep 12, 2014 | 1991 Toyota MR2

1 Answer

Running lights going out while driving

If the problem is occurring or corrected while wiggling the switch, remove the switch assembly and check for loose ,corroded or burnt harness connection. if it looks ok, problem may be within the switch itself, replace the switch assembly and recheck.

Jan 04, 2014 | 1984 Nissan Pickup

1 Answer

My 99 passatt 1.8 turbo couple of week ago I replace passager side head light then two weeks later I replace the same bulb it work for about 3 weeks then one day no drl and no regular head lights just...

Its a German car and they are known for electrical problems. Your problem lies within the Drivers light assembly, check the voltage voming into the headlight socket with multimeter and see if there are any voltage spikes or drops, alternating.

Oct 16, 2013 | Cars & Trucks

1 Answer

How to replace head light

The headlight replacement procedure.:---
  • Apply the parking brake and open the hood.The head is attached by thumb shaped screw.You will see the thumb screw on the upper inboard corner of the turn signal assembly Remove the screw with the screwdriver.Pull the turn signal assembly outward away from the fender and then disconnect the bulb.Turning the socket and wire 1/4- counterclockwise. Set the turn signal assembly aside.Disconnect the electrical connector plug from the headlight being replaced. Lift up on the blue retaining clip of the plug and pull it away from the socket of the headlight.Turn the black retaining collar of the headlight counterclockwise to remove it and the headlight from the headlight assembly.Install the new headlight by reversing the procedure.Replace the turn signal bulb into its assembly and reinstall the assembly and thumbscrew.


  • Nov 12, 2010 | 2005 Pontiac Montana SV6

    1 Answer

    Changing the headlight on a 2006 pontiac g6

    To replace the headlight bulbs.You need to remove the head light assembly out.The head light assembly is held by 2 to 3 three screws on each side. You need to remove those screws first.The front trim will get loose,the front trim is held by pins.The pins are of plastic and easy to release.Just release this pins and the front trim will get completely loose and can be easily taken off/. The head light assembly is in the front fender.Once the front trim is removed the head light assembly can be easily removed from front fender compartment.If its bit tight there,then you can use a screwdriver to give it a pull towards out.The head light bulbs can now be easily seen as well as easily removed now.Turn the bulb socket counterclockwise to remove the bulb from the bulb assembly. -------- Keep updated for any more queries.Thanks.

    Oct 14, 2010 | 2006 Pontiac G6

    1 Answer

    Head lighs

    Sounds like you have a bad dimmer switch. That switch is mounted on the top of the steering column but is not too bad to change. You will need to take out the panel under the steering column and remove the nuts holding it up to allow it to dorp a few inches. With that done its just a matter of 2 bolts to remove the switch.

    Jul 09, 2010 | 1983 Chevrolet Chevy

    1 Answer

    I would like to replace the headlight assembly of a 2008 Silverado. I've located 3 bolts and removed them but am unable to remove assembly. Is it possible to replace the head light assembly without...

    There is a little aluminum stick in the assembly holding it in. On the top of the headlight twist the stick and remove it. It will look like a tent stake. Remove this stick and then the head light assembly will almost fall out.

    Apr 27, 2010 | 2007 Chevrolet Silverado 2500HD

    1 Answer

    Head lighs go out on 98 cutlass oldsmobile when put on high beam.

    You probably have a defective high/low beam switch. You'll have to have the lever assembly replaced. This is a common problem on Olds and Buick cars of that year. The switch is about $75 on the internet. I wouldn't try replacing it myself as you might deploy the air bag... Call around to a REPUTABLE auto repair shop. They probably have replaced a few and should give you an idea of the total cost. Should be about $75- $100 for labor. Good Luck ! ! ! !

    Dec 06, 2009 | Oldsmobile Cutlass Cars & Trucks

    1 Answer


    why not just disable the motors while in up position?

    Aug 25, 2009 | 1998 Chevrolet Corvette

    2 Answers

    2005 Dodge 1500 code p0404 EGR valve.

    The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

    1. Remove electrical connector (5) at top of EGR valve solenoid.
    2. Remove tube mounting bolt (1) at intake manifold.
    1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
    2. Remove gasket located between EGR tube flange and EGR valve assembly.
    3. Remove two EGR valve mounting bolts (5).
    4. Separate valve assembly (3) from engine.
    5. Remove and discard metal gasket located between cylinder head and valve assembly.
    1. Clean area at rear of left cylinder head where it joins base of EGR valve.
    2. Clean EGR tube where it joins EGR valve.
    3. Position new gasket between EGR valve and cylinder head.
    4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
    5. Position new gasket between EGR tube flange and EGR valve assembly.
    6. Position EGR tube (1) to side of EGR valve and into intake manifold.
      1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
      2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

    Feb 05, 2009 | 2005 Dodge Ram 1500

    Not finding what you are looking for?
    1998 Plymouth Grand Voyager Logo

    Related Topics:

    24 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Plymouth Experts


    Level 3 Expert

    81400 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22359 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Plymouth Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides