Question about 1994 Oldsmobile Eighty Eight

1 Answer

Turn signal lights dont work checked fusses flashers work and bulbs r al good whats next

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

You have a relay from the turns signal its located under the hood in the fuse box.

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause turn signals,and flashers to stop working,and bulbs are good


bad earth to the ofending lights, burnt out flasher unit, worn switch. all assuming youv checked the fuse fisrt, after that check the flasher unit which should be in or near the fuse box and it will look like a rely so make sure youv got the manual or guide book befor you start pulling out the relays

Jul 30, 2014 | 1997 Mercury Mountaineer

2 Answers

Turn signal flashes fast but bulbs good


Under the dashboard there is a round metal device called a flasher its where the tick noise comes from when you activate your turn signal I would try replacing that next Good luck

Apr 04, 2014 | Toyota Camry Cars & Trucks

2 Answers

Tail lights not working


ck fuse for rear taillights tis under the dash lower left of steering wheel. or if you still have the manual look in there under fuses.
also look for a bad ground but i doubt that.. if it's both rear out.
fast flashing well here's a chart with all sorts of info.
Problem What To Do Turn signals light, but do not flash Replace the flasher No turn signals light on either side Check the fuse. Replace if defective.
Check the flasher by substitution.
Check for open circuit, short circuit or poor ground. Both turn signals on one side don't work Check for bad bulbs.
Check for bad ground In both housings. One turn signal light on one side doesn't work Check and/or replace bulb.
Check for corrosion in socket. Clean contacts.
Check for poor ground at socket. Turn signal flashes too fast or too slow Check any bulb on the side flashing too fast. A heavy-duty bulb is probably installed In place of a regular bulb
Check the bulb flashing too slow. A standard bulb was probably installed in place of a heavy-duty bulb
Check for loose connections or corrosion at the bulb socket Indicator lights don't work in either direction Check If the turn signals are working
Check the dash indicator lights
Check the flasher by substitution One Indicator light doesn't light On systems with 1 dash indicator:
- See if the lights work on the same side. Often the filaments have been reversed In systems combining stoplights with taillights and turn signals
- Check the flasher by substitution On systems with 2 Indicators:
- Check the bulbs on the same side
- Check the indicator light bulb
- Check the flasher by substitution
hope this helps. may want to print for future reference. :)
hope this helps.

Dec 31, 2017 | GMC Suburban Cars & Trucks

2 Answers

My singal light work then dont work what could cause that?


you may have a burned light bulb or it may be loose check it out

Sep 08, 2011 | 2000 Oldsmobile Intrigue

1 Answer

My saturn signal light work sometime than go off if it the flasher please tell me there it is in my car


IF TURN SIGNAL LIGHT DONT WORK SOME TIMES.CHECK FOR BLOWED OR LOOSE FUSE.CHECK TURN SIGNAL BULBS AND CHECK BULB SOCKETS FOR CORROSION.CHECK TURN SIGNAL FOR BAD GROUND.USE JUMPER WIRE BETWEEN GROUND SIDE OF THE TURN SIGNAL BULBS AND A GOOD CHASIS GROUND.IF ALL IS GOOD TURN SIGNAL SWITCH IS BAD OR FLASHERS GOING BAD.TURN SIGNAL FLASHER LOCATED ON CENTER CONSOLE SIDE PANEL GRASP THE FLASHER UNIT AND DETACH IT FROM THE FUSE BOX.IF YOU HAVE EARLY MODEL VECHICLE FLASHER UNIT LOCATED AT THE FRONT OF THE FUSE BLOCK.

Aug 23, 2011 | Saturn LS Cars & Trucks

2 Answers

I have turnsignals problem on 92 buick lasabre limited i replaced flasher, all bulbs are good. if i manually move the turnsignal lever up and down the bulbs will flash also hazard lights work what else can...


When you say you replaced "flasher" I'm guessing you mean the combination turn signal flasher unit. If the hazards "flash" on the 4 way but the turn signal does not you are looking at a turn signal switch type problem. ... If 4way flashers do NOT work you need to check wiring immediately around the flasher unit mounting area.Or change Flasher unit Good Luck.

Apr 11, 2010 | 2000 Buick LeSabre

2 Answers

No signal lights


there are two different relays for flasher and turn, I would check the turn signal relay, if seems good I would check the switch.

Nov 11, 2009 | 2002 Dodge Durango

2 Answers

Turn signals dont work bulbs/fuses are good.


check to see if the emergency flashers work if they do its its either a wiring problem, bulb, or socket the bulb fits in. if it does not work than the flasher is the problem. it is located underdash on driver side in the kick panel( to left of the brake pedal) it is a blue or grey sguare relay looking plug. if it is factory flasher it will say flasher with the part # on it. it should also say toyota on it. good luck

Jul 09, 2009 | 2000 Toyota Camry

3 Answers

Blinkers not working


Did you check the bulbs? If one bulb is burned out, the blinkers won't word on that side. You could have one bulb burned out on each side. Start the car, put left signal on. Check front and back lights. Is one light on but not blinking? If that's the case, the light that's not on at all is burned out and has broken the circuit so the good light stays on and won't blink. Check the other side. You also have a 'flasher' , actually 2. One for emergency flashers, one for the turn signals. It could be that the turn signal flasher is shot. You just have to unplug it to remove. It's probably located near the fuses. good luck countrycurt0

Aug 10, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Oldsmobile Eighty Eight Logo

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...