Question about 1987 Ford Bronco

1 Answer

I installed a steering column in my 87 Bronco from another one. There is a wiring harness coming from the steering wheel about 16 inches long with a female plug on the end. There is no visible male plug that matches it. Where does it plug in at?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

There should be a one under the dash that it hooks to, kind of a half moon shaped connector. perhaps it still attached to the one that came out of it?

Posted on Aug 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace headlight dimmer switch on a 2003 chev impala do I have to pull the steering wheel


Yes , the steering needs to be pull .
Disable the SIR system. Refer to SIR Disabling and Enabling in SIR. Remove the steering wheel. Refer to Steering Wheel Replacement . Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement .
Important: The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.
Remove the wire harness assembly (1) from the wire harness strap (2). Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
There could be a video on youtube show how to do it .
Theret

Oct 20, 2016 | Cars & Trucks

1 Answer

How to change ignition lock cylinder


Ignition Lock Cylinder REMOVAL & INSTALLATION NOTE: On 1974-76 models, equipped with A.C.R.S. perform the special procedure for removing the air cushion module from the steering wheel if necessary, prior to removing the lock cylinder. Standard Steering Column
  1. Remove the steering wheel.
  2. Remove the lockplate cover assembly.
  3. After compressing the lockplate spring, remove the snapring from the groove in the shaft. CAUTION
    When the snapring is removed do not allow the shaft to slide out the bottom of the column.
  4. Remove the lockplate, then slide the turn signal cam and the upper bearing preload spring off the upper steering shaft.
  5. Remove the thrust washer from the shaft.
  6. Remove the hazard warning switch from the column along with the turn signal lever.
  7. Use the following procedure if the car is equipped with cruise control.
    1. Attach a piece of stiff wire to the connector on the cruise control switch harness.
    2. Gently pull the harness up and out of the column.
  8. Remove the turn signal switch mounting screws.
  9. Slide the switch connector out of the bracket on the steering column.
  10. After freeing the switch wiring protector from its mounting, pull the turn signal switch straight up and remove the switch, switch harness and the connector from the column.
  11. Turn the ignition switch to ON or RUN, then insert a small drift pin into the slot next to the switch mounting screw boss. Push the lock cylinder tab and remove the lock cylinder.
  12. Installation is the reverse of the removal procedure. Fig. 1: Ignition lock removal - standard column 85878054.gif
Tilt Column
  1. Remove the steering wheel.
  2. Remove the rubber sleeve bumper from the steering shaft.
  3. Using an appropriate tool, remove the plastic retainer.
  4. Using a spring compressor, depress the upper steering shaft spring and remove the C-ring. Release the steering shaft lockplate, the horn contact carrier, and the upper steering shaft preload spring.
  5. Remove the four screws which hold the upper mounting bracket, then remove the bracket.
  6. Slide the harness connector out of the bracket on the steering column. Tape the upper part of the harness and connector.
  7. Disconnect the hazard button and position the shift bowl in Park. Remove the turn signal lever from the column.
  8. Use the following procedure for cars with cruise control.
    1. Remove the harness protector from the harness.
    2. Attach a piece of piano wire to the switch harness connector.
    3. Before removing the turn signal lever, loop a piece of piano wire and insert it into the turn signal lever opening. Using the wire, pull the cruise control harness out through the opening.
    4. Pull the rest of the harness up through and out of the column.
    5. Remove the guide wire from the connector and secure the wire to the column.
    6. Remove the turn signal level.
  9. Pull the turn signal switch up until the end connector is within the shift bowl. Remove the hazard flasher lever. Allow the switch to hang.
  10. Place the ignition key in the run position.
  11. Depress the center of the lock cylinder retaining tab with a small prytool, then remove the lock cylinder. On some model remove the lock cylinder retaining screw. To install:
  12. When assembling the lock cylinder, rotate the key to the stop position while holding the cylinder and push the cylinder in all the way.
  13. Install the retaining screw on those models so equipped, and tighten to 40 inch lbs. (4.5 Nm).
  14. Install all components in the reverse of the removal procedure order. Check switch for proper operation. Fig. 2: Installing ignition lock - tilt column 85878055.gif
    prev.gif next.gif

Jan 14, 2011 | 1989 Cadillac Sedan DeVille

2 Answers

The horn doesn't blow. at the horn relay,jumping 30/87 and the horn blows. terminal 85 is always +[positive],and this is correct.Terminal 86 is the ground for the 85/86 side of the relay. If I have the...


Your problem is most likely a defective clockspring assembly. This is also called "spiral cable assembly" it is located just under the steering wheel on the steering column and makes the connection between the main wiring harness and the circuits for the air bag and the horn. I cannot give you wire colors because your question did not mention year, make, model, engine size or whether the vehicle is equipped with cruise control or not. (cruise control makes a difference in the clockspring assembly used on your car.)

Anyway, the air bag and steering wheel has to be removed to fix it.

Dec 19, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

1 Answer

2001 jeep grand cherokee laredo, lights come one intermittently, horn came on unexpectedly and wouldn't turn off. How do I fix that?


Lights intermittent can be caused by switch or relay. Try swapping the Low Beam relay with another similar relay (horn relay is a good choice) to see if that resolves it. These relays are in the Junction Block--may be under the hood or in the car but not in the big box by the battery). If this doesn't fix it, the problem is likely the headlamp switch.

Horn coming on is usually caused by a broken switch or stripped wire insulation inside the steering column. You would usually have to take the steering wheel off to fix it, and this requires special tools; however, if the problem happens to be under the steering column shroud, you may be able to fix it without taking off the steering wheel. Take the shroud off and see if you can follow the black/red horn wire. Follow it as far as you can to check for stripped insulation contact with any metal. If you lights switch is bad, you can also change that while you have the shroud off.

Please let me know if you have questions.


jturcotte_35.gif
jturcotte_36.gif


Wand Removal & Installataion

  1. Disconnect and isolate the battery negative cable.
  2. Remove the knee blocker from the instrument panel.
  3. Remove the three screws that secure the lower steering column shroud to the upper shroud.
  4. If the vehicle is equipped with a standard non-tilt steering column, loosen the two upper steering column mounting nuts. If the vehicle is equipped with the optional tilt steering column, move the tilt steering column to the fully lowered position.
  5. Remove both the upper and lower shrouds from the steering column.
jturcotte_37.gif

Fig. Steering column shroud removal for the Cherokee

  1. Remove the two screws that secure the multi-function switch water shield and bracket to the top of the steering column.
  2. Remove the one screw located below the left multi-function switch control stalk that secures the multi-function switch water shield and bracket to the steering column.
  3. Gently pull the lower mounting tab of the multi-function switch water shield bracket away from the steering column far enough to clear the screw boss below the left multi-function switch control stalk.
  4. Lift the water shield and bracket with the left multi-function switch off of the left side of the steering column far enough to access the two instrument panel wire harness connectors for the left multi-function switch.
    NOTE If the vehicle is equipped with the optional tilt steering column, lifting gently upward on the tilt release lever will provide additional clearance to ease left multi-function switch removal.
  5. Disconnect the two instrument panel wire harness connectors from the left multi-function switch connector receptacles.
  6. Remove the left multi-function switch and water shield from the steering column as a unit.
  7. Gently and carefully remove the water shield from the switch by pulling it over the hazard warning switch button and the left multi-function switch control stalk.

To install:
  1. Gently and carefully install the water shield onto the switch by pulling it over the hazard warning switch button and the left multi-function switch control stalk.
  2. Position the left multi-function switch and water shield near its mounts on the steering column as a unit.
  3. Reconnect the two instrument panel wire harness connectors to the left multi-function switch connector receptacles.
  4. Position the left multi-function switch onto its mounts on the left side of the steering column.
    NOTE If the vehicle is equipped with the optional tilt steering column, lifting gently upward on the tilt release lever will provide additional clearance to ease left multi-function switch installation.
  5. Position the lower mounting tab of the multi-function switch water shield bracket to the steering column screw boss below the left multi-function switch control stalk.
  6. Install and tighten the one screw located below the left multi-function switch control stalk that secures the multi-function switch water shield and bracket to the steering column.
  7. Tighten the screw to 10 inch lbs. (1.1 Nm).
  8. Install and tighten the two screws that secure the multi-function switch water shield and bracket to the top of the steering column [Tighten the screws to 20 inch lbs. (2.2 Nm)].
  9. Position both the upper and lower shrouds onto the steering column.
  10. Install and tighten the three screws that secure the lower steering column shroud to the upper shroud. Tighten the screws to 18 inch lbs. (2 Nm).
  11. If the vehicle is so equipped, tighten the two nuts that secure the non-tilt steering column upper mounting bracket to the dash panel steering column support bracket studs. Tighten the nuts to 200 inch lbs. 22 Nm).
  12. Reinstall the knee blocker onto the instrument panel.
  13. Reconnect the battery negative cable.

Nov 04, 2010 | 2001 Jeep Cherokee

1 Answer

I need to put in another steering collum and I dont know how to do it.its a 91 ford F150.hope you can help me.I got another one out of the junk yard for 125,00 is that a good price .thanks for helping my...


I'd say $125.00 is a good price for a steering column.

First, have to remove steering wheel (but I don't have instructions for the steering column. For that, maybe try alldata.com, but that will cost):

STEERING Steering Wheel REMOVAL & INSTALLATION Without Air Bag EXCEPT F-SUPER DUTY STRIPPED CHASSIS MODELS AND MOTOR HOME CHASSIS MODELS Fig. 1: Remove the screws from behind the wheel - F-150 model without air bag 88288p12.jpg
Fig. 2: Pull away the cover with the wiring still connected 88288p13.jpg
Fig. 3: Disconnect the wiring at the steering wheel 88288p14.jpg
Fig. 4: Matchmark the steering wheel 88288p15.jpg
Fig. 5: Remove the center nut from the steering wheel 88288p16.jpg
Fig. 6: Use a steering wheel puller to remove the wheel 88288p17.jpg
Fig. 7: Remove the steering wheel from the shaft 88288p18.jpg
Fig. 8: Correct steering wheel installation 84928058.gif
NOTE: The factory recommends that the front wheels be set in the straight-ahead position and you paint or make chalk marks on the column and steering wheel hub for alignment purposes during installation. Of these two safeguards, it is more important to mark the column so even if the column is moved slightly, the steering wheel can still be repositioned in its original position.
  1. Disconnect the negative battery cable.
  2. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel. On vehicles equipped with the sport steering wheel option, pry the button cover off with a suitable prytool.
  3. Disconnect the horn switch wires at the connector and remove the switch assembly. On trucks equipped with speed control, squeeze the J-clip ground wire terminal firmly and pull it out of the hole in the steering wheel. Don't pull the wire out without squeezing the clip.
  4. Remove the horn switch assembly.
  5. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
    Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
  6. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 40 ft. lbs. (54 Nm)
F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS MODELS
  1. Set the front wheel in the straight-ahead position and make chalk marks on the column and steering wheel hub for alignment purposes during installation.
  2. Disconnect the negative battery cable.
  3. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel.
  4. Disconnect the horn switch wires at the connector and remove the switch assembly.
  5. Remove the horn switch assembly.
  6. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
    Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
  7. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 30-42 ft. lbs. (41-57 Nm).
With Air Bag Fig. 9: Remove the air bag module and disconnect the wiring harnesses 88288g00.gif
CAUTION
Read the air bag service precautions in Section 6 prior to doing work involving an air bag equipped steering column component. Always wear safety glasses when servicing an air bag vehicle and handling the air bag to avoid possible injury.
  1. Turn the front wheels to the straight-ahead position.
  2. Disconnect the battery-to-starter relay cable for at least one minute to let the air bag back-up power supply discharge.
  3. Remove the air bag module from the steering wheel (refer to Section 6).
  4. Disconnect the horn/speed control wiring from the steering wheel.
  5. Remove the steering wheel retaining bolt.
  6. Install the Differential Bearing Cone Remover/Replacer, No. T77F-4220B1, or equivalent, and remove the steering wheel. Route the contact assembly harnesses through the steering wheel as it is lifted off of the shaft. To install: NOTE: Make sure the front wheels are still in the straight-ahead position prior to installation.
  7. Route the air bag sliding contact wiring through the steering wheel at the 3 o'clock position. Position the steering wheel on the shaft an align the marks. Make sure not to pinch the contact wire. WARNING
    Make sure no air gets trapped between the steering wheel and air bag sliding contact.
  8. Install a new steering wheel retaining bolt, then tighten to 23-33 ft. lbs. (31-45 Nm).
  9. Connect the horn/speed control wiring and clip in place. Connect the air bag wire harness. Tighten the module retaining nuts to 35-53 inch lbs. (4-6 Nm). NOTE: When the battery cable has been disconnected, then reconnected, some abnormal driving symptoms may occur for the first 10 miles (16 km) until the PCM re-learns it adaptive strategy.
  10. Connect the battery to starter cable. Verify the air bag warning indicator light on the instrument panel.
prev.gif next.gif

Sep 24, 2010 | 1991 Ford F150

1 Answer

How do i remove the turn signal switch on a 2001 chevy impala


Removal & Installataion
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
  • Remove the upper and lower steering wheel trim covers using the following procedure.
    • Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
  • Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
  • Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
  • To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.

    Mar 06, 2010 | 2001 Chevrolet Impala

    1 Answer

    I need to install my cruise control switch on my steering wheel . How do I go about removing the back cover on the steering wheel?


    Removal & Installataion
    1. Verify that the multifunction turn signal lever is in the center of the OFF position.
    2. Disconnect the negative battery cable.
    3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
    4. Remove the air bag module from the steering wheel.
    5. Remove the steering wheel.
    ca4e20e.gif
    Exploded view of the shroud-type steering column showing shrouds, wiring and multifunction switch that includes the headlamp function

    1. Remove the upper and lower steering wheel trim covers using the following procedure.
    2. Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
    1. Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
    2. Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
    To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.
    1. Disable the SIR system.
    2. Remove the upper and lower trim covers.
    3. Remove the knee bolster.
      NOTE The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.

    4. Remove the wire harness assembly from the wire harness strap.
    5. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
    6. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
    7. Remove the 2 pan head tapping screws and from the turn signal and multifunction switch assembly.
    8. Remove the turn signal and multifunction switch assembly from the steering column tilt head assembly.
    To install:
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    CAUTION Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

    CAUTION The abrasion sleeve must be installed back onto the steering column wire harness assembly. The ignition lock cylinder case wires and connector must be hanging out of the middle of the abrasion sleeve.

    1. To install, reverse removal procedure.
    2. Tighten the following to specification.
      • Top pan head tapping screw: 27 inch lbs. (3 Nm).
      • Side pan head tapping screw: 62 inch lbs. (7 Nm).
    CAUTION When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

    Dec 08, 2009 | 2005 Chevrolet Impala

    1 Answer

    Steering column


    1. Set the parking brake.
    2. Disconnect the battery ground cable.
    3. Unbolt the intermediate shaft from the steering column.
    4. Disconnect the shift linkage rod(s) from the column.
    5. Remove the steering wheel.
    If you have a tilt column, the steering wheel MUST be in the full UP position when it is removed.
    1. Remove the floor cover screws at the base of the column.
    2. Remove the steering column shroud by place the bottom screw in the No.1 position and pulling the shroud up and away from the column.
    3. On automatics, remove the shift indicator cable.
    4. Remove the instrument panel column opening cover.
    5. Remove the bolts securing the column support bracket to the pedal support bracket.
    6. Disconnect the turn signal/hazard warning harness and the ignition switch harness.
    7. Lift the column from the vehicle.
    8. Remove the column support bracket
    To install:
    1. Install the column support bracket making sure that the wiring is outboard of the column. Torque the nuts to the specifications shown in the Torque Chart at the end of this Section.
    2. Start the floor cover clamp bolt and press the plate until the clamp flats touch the stops on the column outer tube.
    3. Install the column through the floor opening.
    4. Connect the turn signal/hazard warning and ignition harnesses.
    5. Raise the column and install the 2 support bolts.
    6. Tighten the floor cover bolts to the specifications shown in the Torque Chart at the end of this Section.
    7. Torque the support bracket bolts to the specifications shown in the Torque Chart at the end of this Section.
    8. Torque the cover plate clamp bolt to the specifications shown in the Torque Chart at the end of this Section.
    9. Install and adjust the shift indicator cable, on automatics.
    10. Install the instrument panel column opening cover.
    11. Install the column shroud.
    12. Torque the shroud bottom screw to 15 inch lbs.
    13. Connect the shifter rod(s).
    14. Connect the intermediate shaft. Torque the bolt to the specifications shown in the Torque Chart at the end of this Section.
    Good luck...

    Nov 01, 2008 | 1983 Ford F150

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    70 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5516 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...