Question about 2004 Saab 9-3

Open Question

How do I remove the solenoid for the steering lock

04 Saab 9-3 removal of the steering lock solenoid under the steering column

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2039 Answers

SOURCE: Short in steering column wiring

torque bit 20 to remove the air bag bolt in the back cover stering puller stering puller to push plate phillip screw driver that about it pierre

Posted on Oct 19, 2008

Ad
bibleman01
  • 334 Answers

SOURCE: remove rear wiper blade on saab 9-5 estate

Best way go to a parts store and ask for help and they would probably slip it on for you
God Bless you Greg

Posted on Dec 03, 2008

  • 1 Answer

SOURCE: 1999 saab 9-3 wheel bearing removal

You need air tools, many differnet size sockets and a press. The strut/spindle and lower control arm have to come out all together. leaving the axle in the car.The spinlde cannot be removed from the strut. once removed, you can then unbolt the lower control arm ball joint nut, and seperate the lower control from the spindle - for ease for the press. press the hub out, remove the snap rings on either side and press the old bearing out. press in new bearing , install snap rings, press the hub in and reinstall. I just did one today... I have 15 years experience as a ford tech - Ugh bro.. - Josh

Posted on Dec 14, 2008

  • 1 Answer

SOURCE: how to remove a radiator

go to the saabsite for istructions.no you dont if you dont mind ripped up hands...I did it in two hours..definately need heavy duyt lifts\\

Posted on Apr 27, 2009

  • 1 Answer

SOURCE: oil change

07 saab 93 oil filter location. Is it under the plastic cover on top of the engine?

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i fix a no cranck no start?


Sounds like the infamous steering column lock failure. They have a cheaply made electric motor that goes bad, which if not working properly endangers the driver due to possible inadvertent column lock.
25704481-xk2nq4st5s532yy3edhn5dbn-3-0.jpg Extremely difficult to remove if stuck in the lock position. Drilling and cutting required. If you buy a replacement used one be sure the part number matches exactly. You could theoretically just plug the replacement column lock module in to the wire harness and secure it under the dash to satisfy the security protocol (to clear the warning light to let the car run). You would be safer due to less risk of the column locking while driving but at a slightly higher risk for theft or roll away due to the column being free all the time. Only do any of this at your own risk. Good Luck!

May 20, 2015 | 2004 Saab 9-3

3 Answers

How to remove ingition housing from steering column


Welcome to Fixya

Thank you for bringing up the problem to our attention. To serve you better, could you please provide me the exact year model of your car.

Your response will be greatly appreciated.

Thank you for using Fixya!

Aug 26, 2011 | Saturn Ion Cars & Trucks

1 Answer

My steering lock jammed on my Saab 9-3 vector 08.?


Could be a couple of things
Is key turning and car starting?
These give loads of trouble
Steering lock can be removed easily enough

Jun 09, 2011 | 2008 Saab 9-3

1 Answer

I need to brake out a tumbler from the ignitions switch on a 1999 saab 9/3


  1. First your gonna remove the screws on the side steering cover itself.
  2. Now remove the screws on the bottom of the steering column cover.
  3. Pull the bottom half of the steering column off.
  4. Now you will see a little hole by the bottom of the tumbler.
  5. take a punch and insert it into that hole.
  6. With the punch pry up a bit and pull the tumbler out.

Regards, Tony

May 02, 2011 | Saab 9 3 Cars & Trucks

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

2003 ford explorer is stuck in park, the brake lights are on so i dont think it is something to do with the brake


adobe.gif Printable View (109 KB) TSB
04-22-12
  • GEAR SELECTOR LEVER - INCREASED EFFORT TO SHIFT FROM DRIVE TO PARK
Publication Date: November 1, 2004
FORD: 2002-2005 Explorer, Mountaineer ISSUE: Some 2002-2005 Explorer 4dr/Mountaineer vehicles, may require a greater effort to move the gear selector lever (shift lever) from drive to park. This may be due to a time delay with the brake shift interlock (BSI) pin retraction.
ACTION: To service, replace the BSI switch. Refer to the following Service Procedure.
SERVICE PROCEDURE
  1. Remove the two (2) fasteners supporting the instrument panel knee bolster from below the steering column and remove the cover (Figure 1).

    tb7934b.gif
    Figure 1 - Article 04-22-12

  2. Remove the three (3) fasteners supporting the steering column lower shroud and remove the cover (Figure 2).

    tb7935b.gif
    Figure 2 - Article 04-22-12

  3. Remove the three (3) wiring bundle carrier fasteners from the bottom of the steering column to allow movement while removing the BSI switch. It may be necessary to release the connectors from the multifunction switch (Figure 3).

    tb7936b.gif
    Figure 3 - Article 04-22-12

  4. Remove the BSI fasteners (T-30 on the side and T-20 on the bottom) (Figure 4).

    tb7938a.gif
    Figure 4 - Article 04-22-12

  5. Pull the BSI tab on the bottom of the column downward to help free the BSI from the column housing.
  6. Break the two (2) side tabs off the BSI by the white wiring connector (Figure 5).

    tb7940a.gif
    Figure 5 - Article 04-22-12

  7. Push the locking tab on the white connector towards the wiring to release the connector from the BSI. Be careful not to damage the connector or wiring. If the connector does not free easily, a very small flat screwdriver may be used to help lift the locking tab (Figure 6).

    tb7941a.gif
    Figure 6 - Article 04-22-12

  8. Connect the wiring to the new BSI. Ensure all clips are fully engaged to prevent the connector from pulling free.
  9. Reinstall the BSI onto the steering column and reinstall fasteners (Figure 7).

    tb7942a.gif
    Figure 7 - Article 04-22-12

  10. Check BSI function. With the key in the accessories or run position, press the brake pedal. The BSI pin should retract on brake application, and spring up one (1) second after releasing the brake pedal. Repeat several times.
  11. Reinstall fasteners to connect wiring bundle carrier to the steering column. Make sure all connections to the multifunction switch unit are secured properly.
  12. Reassemble steering column in reverse order. Ensure rubber gap hider around shift lever is properly seated on the shroud.
  13. Cycle the shift lever from park to drive and drive back to park several times to verify improved shift effort.

PART NUMBER PART NAME 1L2Z-3Z719-DA BSI Switch

Feb 15, 2011 | Ford Explorer Cars & Trucks

2 Answers

A warning light showing "steering lock malfunction" came on then disappeared - twice. What's the problem and is the car safe to drive?


If the SID Unit (or profiler) displays "Steering Lock Malfunction" get to your local dealer promptly. There has been issues with the steering lock module and they are now being replaced by Saab under warranty. The module is located under the steering column and must be replaced depending on the part number on the module itself. See your local dealer to find out if your module needs to be replaced.

Jun 09, 2009 | 2003 Saab 9-3

1 Answer

I want to pull it


what year?

1999 electrcial ign switch. Lock cylinder is different

211-05: Steering Column Switches 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Position the LH instrument panel insulator aside.
    1. Remove the pin-type retainers.
    1. Position the insulator.
  1. Remove the LH instrument panel insulator.
    1. Disconnect the courtesy lamp.
    1. Remove the insulator.
  1. Remove the lower instrument panel steering column opening cover.
    • Remove the screws.
    • Unhook the parking brake release handle and position aside.
    • Remove the cover.
  1. Remove the five bolts to remove the instrument panel steering column opening cover reinforcement.
  1. Disconnect the ignition switch electrical connector.
    1. Loosen the bolt.
    1. Disconnect the electrical connector.
  1. NOTE: The ignition key should be in the OFF position.
    Remove the ignition switch.
    1. Remove the bolts.
    1. Remove the switch.
---------------------
SECTION 211-04: Steering Column 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder —Functional Lock Cylinder Removal
  1. Disconnect the battery ground cable; for additional information, refer to Section 414-01 .
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key and turn to the RUN position.
    1. Press the ignition switch lock cylinder release pin while pulling out the ignition switch lock cylinder.

86b3f2f.gif

Apr 25, 2009 | Lincoln Town Car Cars & Trucks

1 Answer

Remove ignition tumbler


lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.




  1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
  1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.


    0764353.gif

  1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.




  1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
Installation
  1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
  1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
  1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
  1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
  1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
  1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
  1. Connect the ignition switch electrical connector.
  1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
  1. Install the steering wheel. Refer to the procedure in this section.
  1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.

Apr 07, 2009 | 1995 Mercury Tracer

3 Answers

Oil change


Yes, filter is under plastic cover, and be sure to use SYNTHETIC OIL ONLY! Good luck!

Jul 04, 2008 | 2004 Saab 9-3

Not finding what you are looking for?
2004 Saab 9-3 Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...