Question about 1993 GMC Jimmy

1 Answer

The injetors not fireing - 1993 GMC Jimmy

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 6,927 Answers

Pickup coil in the distributor is what makes the injectors pulse,this is the most likely problem,please rate,thank you

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i am not sure were to go from here i have a rodeo 1997 turbo diesel lx ,it wot start now i have looked at fuel i have checked and tested the glow plugs they are fine iialso dod a moanual test with the...


remember the 3 components fuel, fire and oxygen, if the fuel is coming then its the fire because if there was spraying gas and there was nothing it got to be the fire.

Jan 07, 2014 | Cars & Trucks

1 Answer

Car is hard to start and drains the battery really fast


could have water in gas and restricted fuel filter.make sure reconnect ignition coil pack electrical wires connectors to coil primary circuit and the ignition module.make spark plugs wires put back in the same firing order.

Feb 12, 2013 | 2002 Buick LeSabre

1 Answer

Wire diagram for the fuel injectors on a saturn sl1


firering order should be on in take manofold fuel injector are in harness should only fit on one way

Aug 31, 2012 | Saturn SL1 Cars & Trucks

1 Answer

Starting problem have fire and fuel but still wont start changed pick up coil and ign module


If thats a TBI system..pull the duct work off and see if the injector is flowing a good stream of fuel while you turn it over..Ive seen fuel pumps run and fuel come from the line but not enough flow to make the injetor flow..

Sep 04, 2011 | 1996 GMC Sierra

1 Answer

Have a code p0304 please help on a 5.7eng g1500 savana van 1996


the code that you are receiving is the second cylinder on the passenger side, in otherwords the second spark plug from the front of the motor to the rear.it is not firing properly. now you have to figure out if it is the spark plug or wires or injectors, replace the plugs and wires first, if that doesn't fix than you may need to replace the injetor on number 4 cylinder.

Jul 24, 2010 | 1996 GMC Savana

2 Answers

I have a 1999 gmc Yukon it is getting fuel and spark i even sprayed starter fluid in the intake but it still wont start it turns over good but wont start


ok make sure you have good fuel pressure
you must have good spark must fire a spark tester
if all that is good then check compression
and don't use STARTER FLUID on a GAS ENGINE it can blow a hole through the piston
hope this helps

Nov 12, 2009 | 1999 GMC Yukon

3 Answers

I have a multiple cylinder miss fire i have replaced the ignition coils 3 times and that dont fix it what else could be wrong


Dirty injectors.faulty sensors. You will do alot better if you can find a way to scan the car and view live datastream.

Nov 05, 2009 | 2004 Volkswagen Passat

2 Answers

1997 Chevy Tahoe will crank but will not start.


check the fuse for the injetor. if is bad

Apr 17, 2009 | 2000 Chevrolet Tahoe

1 Answer

I have a 1992 geo prizme with a gass leak at the injetors


This is something you don't fool with; I tried getting injectors on a Jeep tight again when they started bleeding fuel and ended up with an engine fire and replacing the entire harness under the hood. It wasn't fun.
Many injectors are a combination of steel and plastic are are prone to separate with age and too many thermal cycles.
Shop them; the low:high price range is huge.
If you can find the part number for them, check this company as they have always been very competitive:
http://www.fiveomotorsport.com/
  

Sep 25, 2008 | 1992 Geo Storm

Not finding what you are looking for?
1993 GMC Jimmy Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...