Question about 2001 Mazda Tribute

Open Question

Bleeding the new clutch master on a 2001 tribute

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: How do I bleed the clutch master cylinder

Same as You Bleed Any other System Being carefull not to get air IN and IT sometimes TAKES FOREVER ________ STICK WITH IT ------ Took Me 2 hours One time

Posted on Jan 19, 2009

  • 1 Answer

SOURCE: 92 mazda miata new clutch new clutch master

Sounds like the seal in the new clutch master cylinder. I've seen that same problem in the hand brake system in small 2 and 4 seat airplanes. ( I'm and aircraft mechanic) The problem is not air in the lines so bleeding won't help. The piston seal is intermittantly failing to seal. That is whty the function can return without any apparent reason as the seal has seated itself. The only cure is to replace or rebuild the master cylinder. ( Yes, even new or rebuilt ones can have a defective or improperly installed piston seal)

Hope this helps

Posted on Aug 16, 2010

  • 2187 Answers

SOURCE: how too bleed cluch for

Locate the slave cylinder of the clutch system. It should be at the other end of the clutch line found at the transmission.

Loosen the bleed screw a little bit. It should be the one sticking out of it.

Connect a hose that goes to a containing for the fluid that comes out.

With the clutch pedal pressed loosen the screw to release fluid and air.

Repeat the process of pressing the pedal until the air is out of the system. Resistance of the clutch pedal should be back to normal once you tighten the bleed screw.

Posted on Jul 27, 2011

  • 312 Answers

SOURCE: clutch piston too short?

sounds more like a seal to me

Posted on Sep 16, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does the push rod on the clutch master cylinder keep breaking when trying to bleed the system on our 2001 Dodge Neon.

I think there may be two different types of master cylinders -- one uses a longer push rod than the other. If possible, check that the old part is exactly like the new one. If the old part is not available, try getting a knowledgeable parts person to check several year models up and down from yours to see if a different part number exists.

Oct 02, 2016 | 2001 Dodge Neon

2 Answers

New clutch not disengaging

When I do clutch jobs. I replace the clutch package(comes with the slave) and the master cylinder also. Have the flywheel turned or replaced. Just a note. The clutch plate can be installed backwards. No matter how many times you bleed it, It won't work.

May 30, 2016 | 2001 Dodge Ram 3500 Truck

1 Answer

Is it true that u need to bleed a clutch on a mits mirage 2001 car?

If you have replaced the clutch master cylinder or slave cylinder,then you do need to bleed,here's a link on how to bleed your clutch. Repair Guides Clutch Hydraulic System AutoZone com

Oct 05, 2015 | Cars & Trucks

1 Answer

How to change clutch master cylinder

Remove nuts holding master cylinder onto mount. Remove fluid lines carefully, bench bleed new master cylinder then install lines, install mounting nuts then bleed system again applying pressure to clutch pedal several times until no air is seen purging out.

Jun 03, 2015 | 2001 Kia Sephia

2 Answers

04 mazda tribute tryin to bleed brakes did all around but still soft .what am i doin wrong new master cylinder.brakes& front lines.

On top of bleeding at the four corners, you also need to bench bleed the master cylinder whenever it is replaced.

Jan 25, 2015 | 2004 Mazda Tribute

1 Answer

How do you bleed the clutch and slave cylinder on a 2001 chevy blazer?

Usually there is a bleeder screw on the master or the slave, and you bleed it just like you would brakes.
But you should not be loosing fluid if the system is sealed.

Dec 05, 2012 | Cars & Trucks

1 Answer

Have a 2001 honda accord just replaced master clutch cylinder and slave cylinder and clutch won't disengage. what could be the problem.

Did you bleed the clutch hydraulic system after you replaced the parts? It requires bleeding just like the brake system does.

Jul 05, 2011 | 2001 Dodge Ram 2500 Truck

2 Answers

Nissan Sentra won't move.

Most likly needs a new clutch. but before you do that make shore the clutch slave cylinder is releasing.Do this by opening the bleed screw on the clutch slave cylinder. If there is preasure released when you do his you may have a stuck master cylinder. Not likly but worth the trouble to try

Jun 29, 2009 | 2001 Nissan Sentra

1 Answer

How do I bleed the clutch master cylinder

Same as You Bleed Any other System Being carefull not to get air IN and IT sometimes TAKES FOREVER ________ STICK WITH IT ------ Took Me 2 hours One time

Jan 17, 2009 | 2001 Ford Focus

1 Answer

Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Aug 05, 2008 | 2001 Honda Accord

Not finding what you are looking for?
2001 Mazda Tribute Logo

Related Topics:

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides