Question about 2003 Chrysler PT Cruiser

Open Question

How to remove L/F axle shaft on 2003 PT Cruiser?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: front axle how to remove half shaft

Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Posted on Aug 19, 2008

Ad
  • 45 Answers

SOURCE: removing the right intermediate axle shaft

i can only guess it is a 3.0l 4v well as far as the axle goes, the rh outer half shaft seperates at the splines on the intermediate shaft.
the intermediate shaft is the solid shaft from the trans to a bearing support bracket and ends after that. it is externally splined.
the rh axleshaft , inner cv joint, is internally splined.
to remove the rh axleshaft, remove the rh wheel and splash shield.
removed the lower balljoint pichbolt and seperate the lower balljoint front the steering knuckle. take the axle nut off and using a large brass drift or hardwood, drive the axle out of the bearing-hub assembly. DO NOT DAMAGE THE THREADS. also use some lubricant on the axle nut dissasembly. after the outer axle end is free, using the same brass drift or other, hit the inner cv joint and drive it off the intermediate shaft. inspect the splines closely because these fail and cause a no-drive condition.
then the mounint bolts for the support bearing and pull the intermedate shaft out, you will loose some fluid.

Posted on Jan 28, 2009

  • 2 Answers

SOURCE: rear differential axle removal

remove the 'locking bolt', once the pin is out the c-clips shoud fall out unless this is a floating axle in which the axles are attached at the hub.

Posted on Sep 12, 2008

rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

rtpflh
  • 546 Answers

SOURCE: remove/replace alternator chrysler 2004 PT Cruiser

you may have to raise vehicle,remove wheel & plastic inner fender & take it out through the wheel well.it can still be like a chinese puzzle.

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing 2003 pt cruiser driver side quarter window i need to know how to remove trim around quarter window to access the bolt holding window in place


If you pick up either a Chilton or Haynes manual for Chrysler PT Cruiser 2001 -2010 it has some very good instructions and photos

Feb 17, 2017 | 2003 Chrysler PT Cruiser

1 Answer

2003 pt cruiser knob won't turn to defrost


The diverter control unit maybe blocked, check the knob hasn't worn out by pulling it off and trying to turn the shaft with pliers. Turn both ways 90 degrees to see if you get movement.

Oct 13, 2016 | 2003 Chrysler PT Cruiser

1 Answer

Will a spindle off a 2005 automatic PT Cruiser fit on a 2002 manual PT Cruiser


Are you talking the front axle? If yes then according to this Ebay seller it is. If you are getting the axle from a wrecking yard, they should be able to tell you for sure. Two New DTA CV Axles Left Right OE Repl With Warranty Fit PT Cruiser Non...

Jun 14, 2015 | Cars & Trucks

1 Answer

2003 PT Cruiser ODBII code P0443


Take it back to the garage that pu8t the clutch in ,they have disconected or broke a plastic pipe that runs to the fuel tank

Dec 19, 2013 | Cars & Trucks

1 Answer

How do you replace the alternator


The generator is located above the oil filter and axle shaft.
1. Disconnect the negative battery cable.
2. Remove the 2 bolts from the top of the heat shield on the generator.
3. Remove nut from the upper T-bolt adjustment bracket.
4. Raise vehicle and support.
5. Remove the right front wheel.
6. Remove the accessory drive splash shield.
7. Remove the lower heat shield bolt.
8. Remove the generator heat shield.
9. Unplug the field circuit from the generator.
10. Remove the B+ terminal nut and wire.
11. Loosen the accessory drive belt t-bolt.
12. Remove the pencil strut.
13. Loosen the lower generator pivot bolt.
14. Remove the generator belt, refer to the Cooling section for more information.
15. Remove the axle retaining nut.
16. Remove the lower control arm from the steering knuckle.
17. Remove the 2 bolts for the axle shaft bearing support.
18. Remove the axle shaft assembly. Put a container under the transmission to catch the transmission fluid from the transmission.
19. Remove the generator from the lower mounting bracket and set generator to the side.
20 . Remove the lower mounting bracket for the generator.
21. Remove generator through the axle shaft hole.

Jul 29, 2013 | 2006 Chrysler PT Cruiser

1 Answer

How do you the replace alternator


The generator is located above the oil filter and axle shaft.

1. Disconnect the negative battery cable.
2. Remove the 2 bolts from the top of the heat shield on the generator.
3. Remove nut from the upper T-bolt adjustment bracket.
4. Raise vehicle and support.
5. Remove the right front wheel.
6. Remove the accessory drive splash shield.
7. Remove the lower heat shield bolt.
8. Remove the generator heat shield.
9. Unplug the field circuit from the generator.
10. Remove the B+ terminal nut and wire.
11. Loosen the accessory drive belt t-bolt.
12. Remove the pencil strut.
13. Loosen the lower generator pivot bolt.
14. Remove the generator belt, refer to the Cooling section for more information.
15. Remove the axle retaining nut.
16. Remove the lower control arm from the steering knuckle.
17. Remove the 2 bolts for the axle shaft bearing support.
18. Remove the axle shaft assembly. Put a container under the transmission to catch the transmission fluid from the transmission.
19. Remove the generator from the lower mounting bracket and set generator to the side.
20 . Remove the lower mounting bracket for the generator.
21. Remove generator through the axle shaft hole.

Jul 28, 2013 | 2006 Chrysler PT Cruiser

1 Answer

Need to check transmission fluid on pt cruiser


Should be a rubber plug on the left side just above the axle shaft.

Feb 10, 2013 | 2002 Chrysler PT Cruiser

2 Answers

2003 pt cruiser front driver side wheel bearing removal? How do I remove it?


the wheel bearing is pressed into the knuckle and will require a machine shop service to press it in and out.

You will need to remove the knuckle from the vehicle.

-Remove the caliper from the knuckle.
-Remove the rotor.
-Disconnect the ABS harness if equipped
-Remove the bolt that holds the lower ball joint to the knuckle and separate them.
-Remove the outer tie rod from the knuckle.
-Remove the axle nut and tap the drive axle out of the hub.
-Remove the two strut mounting bolts from the knuckle
-Remove the knuckle from the vehicle.

A machine shop or an automotive service facility should be able to press the old bearing out and press in the new bearing for you. Call around for pricing and service availability.

Apr 01, 2011 | 2003 Chrysler PT Cruiser

1 Answer

WHERE IS THE CAM SHAFT POSTIOON SENSOR LOCATED ON A 2003 PT CRUISER


on the upper right of the engine block looking down on it

Oct 20, 2009 | 2003 Chrysler PT Cruiser

2 Answers

Replacing Alternator For 2001 Chrysler PT Cruiser (Manual)


this instruction is general for all vehicles. i am sorry that i do not have particularly for your 2001 chrysler PT cruiser.

first, identify the alternator.
remove the fan belt on the alternator,
label and remove all wires that is attached to it.
remove all bolts that is holding it.
remove the old alternator.

do the reverse on installing it.

tnx 4 using fixya,

drcool

Aug 30, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Chrysler PT Cruiser Logo

Related Topics:

818 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...