Question about 2002 Renault Sportwagon

1 Answer

Megane 1.9 dci the timed wiper switch works the wipers once, the normal speed work fine but the fast speed does not work, but if you leave it it goes to normal speed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Renault Master
  • 22,326 Answers

Listen carefully its a renault ,so it could be anything but i would imagine it needs a new wiper motor

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1985 ford full size bronco changed the wiper switch it has a delay wipers still only work on fast is it the wiper motor that is bad the wiper motor gets wet alot


you need to check the wiring from the switch to the motor with a test light and make sure its switching form the column to the motor ok. you should have a permeant 12v from the battery a permanent earth and then probably 3 more wires, a return signal from the motor to the wiper delay module that tells it when to park and your 2 speed switches from the column- one for normal speed that will go live on first speed and one for fast speed that will go live on second speed- if you have a different number of wires let me know and I should be able to tell you how to test them.

Sep 18, 2017 | Ford Cars & Trucks

2 Answers

What would cause the windshield wipers on my recently purchased Jeep Patriot Sport work on every speed except the high speed. High speed doesn't work at all.


The intermittent switch has a bad contact in it for the high speed, i would say, most likely will have to replace it.

Sep 15, 2014 | 2008 Jeep Patriot Sport

1 Answer

I have 1998 dodge caravan. When you turn on the wipers, it keeps running and never shut off. Eventhough the wipers switch is working on slow and fast speed but when you turn the switch to off position, it...


There is a device made into the wiper motor itself, known as the wiper park switch. Its designed to turn off the wipers at a pre-determined position once you switch them off. The mfr recommends replacing the motor along with the intermittent timer (if equipped) at the same time when experiencing these problems.

Sep 06, 2011 | 1997 Dodge Caravan

1 Answer

Where is the rear wiper relay located on a renault megan x reg 1.9 dci?


There will not be a relay for the wipers. They are powered directly through the switches. The power draw for a wiper motor does not warrant a relay

May 19, 2011 | Renault 181 Cars & Trucks

2 Answers

Wipers don't work on intermittent. They run but stop in they middle of the windshield and don't go to the bottom like normal, Then they run again and stop some other spot. When put on continuous they...


Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper RUN/PARK relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect senses magnet to turn off RUN/PARK sense the output to the windshield wiper RUN/PARK software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.

  • The intermittent windshield wiper speed does not operate correctly
  • Multifunction switch.
  • Circuitry.
  • Windshield wiper motor.
  • Go To Pinpoint Test D .

Pinpoint Test D: The Intermittent Windshield Wiper Speed Does Not Operate Correctly
Normal Operation During normal operation, the windshield wiper motor receives voltage at all times through battery junction box (BJB) fuse 1 (30A), circuit 65 (DG). The windshield wiper motor also receives power with the ignition switch in RUN or ACC positions through central junction box (CJB) fuse 33 (15A), circuit 1002 (BK/PK). Ground is provided to the windshield wiper motor through circuit 676 (PK/OG) and circuit 57 (BK). The run/park and high/low relays are contained in the wiper motor electronics. Mode of operation is dependant on the signal(s) received from the multifunction switch.
    Possible Causes
  • Multifunction switch
  • Open in circuit 57 (BK), 56 (DB/OG), 61 (YE/RD) or 63 (RD)
  • Windshield wiper motor
PINPOINT TEST D: THE INTERMITTENT WINDSHIELD WIPER SPEED DOES NOT OPERATE CORRECTLY Test Step Result / Action to Take D1 CHECK THE MULTIFUNCTION SWITCH
  • Key in OFF position.
  • Disconnect: Multifunction Switch C202b.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to D2 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . TEST the system for normal operation. D2 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between multifunction switch C202b-6, circuit 57 (BK), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes
GO to D3 .

No
REPAIR the circuit. TEST the system for normal operation. D3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD) AND 63 (RD) FOR OPENS
  • Disconnect: Windshield Wiper Motor C125.
  • Using the following table, measure the resistance between multifunction switch C202b harness side and windshield wiper motor C125 harness side:

    Multifunction Switch C202b Windshield Wiper Motor C125 Pin 2, circuit 56 (DB/OG) Pin 10, circuit 56 (DB/OG) Pin 4, circuit 61 (YE/RD) Pin 1, circuit 61 (YE/RD) Pin 1, circuit 63 (RD) Pin 9, circuit 63 (RD) Pin 3, circuit 58 (WH) Pin 11, circuit 58 (WH)
  • Is the resistance less than 5 ohms?
Yes
GO to D4 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. D4 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to D5 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. D5 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as outlined in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by incorrect binding pivot arm adjustment. REFER to Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

Feb 19, 2018 | 2006 Ford F 350 Super Duty

1 Answer

I have a 2004 Ford Focus window won't go down / wiper problem


As far as the window goes, it sounds like your switch is going bad. If you continue to use as it is, the switch will keep getting worse and worse until eventually it doesn't work at all. So you will need to take the inner door panel off and replace the switch. Then the windshield wipers, sounds like a similar problem. However, this time, only part of the electronics are not working properly, but unfortunately you will have to change the whole thing also. The wiper switch is a little more complicated, so if you are not fully familiar with it, you would be better off to take it to someone who is.

Apr 01, 2010 | 2004 Ford Focus

1 Answer

I have a renault megane cabriolet and the intermittent wiper are not working all other speeds are working does anyone know what i need to look at!


Hi, if it is only the intermittent speed that is not working the cause might be the wiper switch that is faulty. You will need to replace the wiper switch.

Nov 24, 2009 | 2006 Renault Le Car

1 Answer

Intermitent Wiper does not work


the most common cause of this is the wiper switch.

Jan 07, 2009 | 1998 Volkswagen Jetta

1 Answer

98 Saturn SL1 Intermittent Wipers stay on full


no this is not an expensive problem. you just need the wiper relay switch.

Dec 14, 2008 | 1999 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

xxxxxx xxx

Level 3 Expert

4979 Answers

Marvin
Marvin

Level 3 Expert

81285 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...