Question about 2000 Buick LeSabre

1 Answer

2000 Buick LeSabre - Interior Drawer below Stereo

My daughter keeps her license in the drawer under the stereo, and somehow it slipped behind the drawer. Do you know how to take the drawer out and re-install it?? Thanks in advance for any assistance you can provide!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

These solutions are not for the question that was asked..I am in the same bingld and need to know how to remove the drawer under the stereo without breaking it....Can anyone help us answer that question

Posted on Jan 29, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 79 Answers

SOURCE: Rear license plate lights burned out and can't

If i remember correctly the entire rear light assembly must be remove in order to access these bulbs. This is true if the license plate is on the trunk. If this is the case then there are nuts on the inside of the trunk that must be removed.

Posted on Aug 14, 2009

  • 11 Answers

SOURCE: How to replace license plate lights (bubs)

I think you have to open the trunk and you can acsess the bulb from behind the open trunk lid.

Posted on Apr 04, 2009

  • 115 Answers

SOURCE: interior lights 1997 buick lesabre won't go off

This is either the switch on the dash or the switch on one of the doors. Make sure that all switches on the doors are properly being contacted by the door. When did you first notice this problem? Had you turned the switch on the dash and then it didn't turn off? That is how I would determine which switch might be the problem. Then you can start by removing the swithes on the doors, unplugging each at a time to see if the light turns off, this will isolate the switch, then I would replace the switch on the dash if none present the problem. I hope this helps.

Posted on Aug 05, 2009

  • 8 Answers

SOURCE: I can't get to the license plate bulb in a buick

There should only ne two little screws on the plastic plate for the bulb. just unscrew and gently pull downward till bulb and harness are exposed. this should be a 194 bulb just pull out and replace with a new one.

Posted on Feb 21, 2010

  • 196 Answers

SOURCE: 2000 Buick Lesabre custom liscense plate bulb

kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have no taillight, license plate light, parking lights or lights behind my stereo keys


check taillight fuse for open owners manuals show locations

Aug 29, 2013 | 2004 Mazda 3

1 Answer

Cigarette lighter not working


Check the ACC fuse under the Hood, there may also be a secondary fuse under the dash in the fuse panel (look at the diagram for that fuse).

it can also be one of the wires slipped out from behind the lighter, Remove the lighter to verify this.. the ACC fuse controls all accessories like the Stereo and such. so if the stereo is working and the fuse's are good changes are its a broken wire or one that became loose. PS check the wires with the IGNITION ON FOR POWER. if there is power replace the lighter unit.

Dec 29, 2012 | 2000 BMW 7 Series

1 Answer

Power seat on 96 Cadillac deville wont work after replacing stereo. Any Ideas?


it is not a fuse, it is a circuit breaker in the fuse box, which i believe is under the hood on that car, i would check for bare or shorted wires behind the stereo before doing anything with the power seat.

Sep 03, 2012 | 1996 Cadillac DeVille

1 Answer

Sound went out in the stereo i was driving and the sound went out in my stock stereo in my 2007 cobalt. the fuses are ok, the stereo light is on. theres just no sound. what can i do?


You might want to check and see if you have somehow lost connection to your speakers. Not familiar with vehicle but I do know stereo's, if the light is on on the Stereo then it should be OK. Check under the dash and around and see if something has come loose going to your speakers. Caution~ DO NOT try to touch another speaker to an existing speaker because if not done properly it will change the speaker resistance and result in a burnt out channel in your stereo.
Gillight

Jul 22, 2012 | Cars & Trucks

2 Answers

Tail lights and dash lights blown out after installing a stereo


make sure the stero ground isn't hooked to a tail light wire,if the lights are off the wire will appear to be a ground.

Mar 17, 2012 | 2000 Honda Accord

1 Answer

Hi my 2003 nissan altima radio not working no sound coming from speaker yet all light are on


Is it a standard version or Bose version? If it's a standard version then either the plug in the back came loose or the built in amp in the stereo is dying. if it's a Bose, then there should be a pre-amp some where under or behind the dash or possibly under or behind the rear seat/ trunk. In that scenario it's possible that the amp has gone bad. Another possibility regardless what version system is installed would be if a wire cracked and is showing somehow, grounding out causing the speakers to go out. Bad ground. maybe a loose plug behind the stereo. Also has the stereo every been replaced. Is it factory stereo and speakers.

Oct 02, 2011 | 2004 Nissan Altima

1 Answer

Changed Radio and now car won't start


What stereo did you use as a replacement? If you used a aftermarket (kenwood, sony, etc) cd player, you need to use the proper adapter harness. These cars have a build in theft deterrent system that involves the stereo. So, when you replace the stereo, a component of your anti theft system is missing. The use of the harness gets around this feature somehow, and allows you to use aftermarket CD players. Also, ensure that no wires are getting pinched behind the stereo, and that all your connections are soldered and shrink wrapped to avoid any future problems. I have provided a link for the correct adapter harness to your vehicle.
http://www.amazon.com/Stereo-Harness-Oldsmobile-wiring-installation/dp/B000KL2PEI

May 03, 2011 | 1999 Oldsmobile Alero

1 Answer

I cant unlock my car stereo and i forgot my personal code


You need to pull the stereo out to get the stereo serial# and then go to the dealership with your driver license along with your car registration. You need to go to service station and they'll get the stereo code# to you. Some dealership they might keep the stereo code in their data bank, so just show them your car registration where they can get your VIN# and they'll get the code# for you.

Sep 27, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

How do i change rear turn signal bulb on 89 corvette, notmine???


Rear Turn Signal, Brake and Parking Lights 1984–89 VEHICLES
  1. If removing an inner bulb, remove the license plate. For outer bulb replacement, reach from under the vehicle.
  2. To remove the inner rear brake light, you must reach behind the license place and under the vehicle to access the bulb and socket
  3. Remove the socket from the lens by releasing the locking tab and twisting
  4. Once the bulb and socket are pulled from the rear of the lens, grasp it from behind the license plate opening
  5. Then, pull it out of the side and replace the bulb
  6. Remove the bulb from the socket and replace.
  7. Installation is the reverse of the removal procedure.

Apr 05, 2009 | 1989 Chevrolet Corvette

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...