Question about Jaguar Xk Series

1 Answer

How difficult is it to change the rubber overriders on the bumpers of an US spec series 3 e type jaguar and to put back on the original chrome overriders (as in the uk spec cars)?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

If you look underneath the bumper it only has a 1/2 inch bolt holding it on.if you can get it off (it may be rusted tight)then one for one.

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace radiator in 2006 Jaguar


if a X type then you take the front of the car off ,its not difficult and should take less than an hour to remove the bumper but you will need to remove the AC rad so the gas will need to be safely removed first by a local garage with a AC machine .

Apr 26, 2016 | Jaguar Cars & Trucks

1 Answer

How to chang a reverse sencor on a s type jaguar


If the faulty sensor is one of the inner sensors the bumper has to come of. If it is a outer sensor only half the bolts on that side have to be removed. Start by partly removeing the under wing shield and there is access to the bolts,open the boot remove plastic shut trim and more bolts. Pull back side carpets remove the black side plates to get to more bolts remove bumper and replace the faulty sensor leave the bumper connected and pointing away and test before refitting.

Mar 24, 2015 | 2002 Jaguar S-Type

1 Answer

Water leak in truck of jaguar


Water leak in trunk may be coming from the vent flaps located behind bumper cover if they stick open water will inter truck while driving in rain if not that you may need to replacle. Rubber seal around trunk

May 25, 2014 | 2000 Jaguar S-Type

1 Answer

My jag series 3 1985 . blows cold air .and blows hot when it wants too .


THEIR IS A VALVE ON THE RIGHT SIDT OF THE VECHILE HEATER VALVE RIGHT AT THE FRONT JUST BEHINED THE BUMPER THAT NEEDS CHANGIND OR CHECK THE CONNECTIOS TO IT FIRST.

Nov 06, 2013 | 2000 Jaguar S-Type

1 Answer

Removing jaguar s type rear bumper..


disconnect the connector from the park aid module push the connector and grommet out of the back panel remove screws from lower rear of wheel arch liners remove boot floor trim remove plastic boot closing panel trim remove both boot side trims you wil find a number of 10mm headed bolts around the boot at the sides and back remove these and get someone to help you remove the bumper liner the 2 outer sensors can normally be changed without removing the bumper liner on some models

Mar 26, 2013 | 2003 Jaguar S-Type

2 Answers

How do you change the headlamp in a 2004 jaguar x-type 3.0?


Open the bonet and look directly behind the headlamp and you should see a black plastic cover with 2 steel clips holding it onto the headlamp. Push the clips to the side and remove the cover. Do not remove completley as it will be difficult to refit. Just so you can get you hand to remove the connector. Remove and replace bulb

Jun 04, 2010 | 2004 Jaguar X-Type

1 Answer

Jaguar x type 2004 front bumper


Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.

Becareful not to damage the fog lamp harness upon removal

Apr 08, 2010 | 2004 Jaguar X-Type

1 Answer

It is so difficult to find a remanufactured power steering pump for a Jaguar 2000 S-Type 3.0L 6 cylinder. Is there another pump that will fit?


Better to use original specs , you should be able to get remanufactured from the dealer and pay the difference , if not , let me know and could probably arrange one for you :)

Jun 27, 2009 | 2000 Jaguar S-Type

1 Answer

S Type Jaguar rear bumper removal


how do you remove a front bumper off of an jaguar s type?

Mar 09, 2009 | 2004 Jaguar S Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...