Question about GMC Sierra 1500

1 Answer

Is it sufficient to remove the EVAP vent solenoid on a 2006 GMC Sierra and clean it out and put it back on?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Yes

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the purge valve on 2006 Yukon Denali


Replacing Vent Valve Solenoid Purge Valve Solenoid EVAP Valve 2005 GMC...

Remove the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement . Remove the evaporative emission (EVAP) line from the canister purge solenoid, perform the following:
2.1.
Push the large size white retainer portion in.


2.2.
Push down, while pulling up slightly in order the disengage the tube.


Disconnect the EVAP canister purge solenoid electrical connector (1).
Remove the EVAP canister purge solenoid bolt (2). Remove the EVAP canister purge solenoid (3) and insulator (1).

Sep 19, 2015 | Cars & Trucks

1 Answer

Where is my vent valve solenoid on my 2006 Chevy Colbalt?


It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

Feb 25, 2015 | Chevrolet Chevy Cars & Trucks

1 Answer

Gas filling


is there an evap code in the computer? normally this is caused by a pinched or stopped up evap line or the vent solenoid is bad not allowing the system to vent pressure which is causing it not to take fuel at a normal rate

Jan 07, 2014 | 2004 GMC Sierra

1 Answer

I have a 2005 Gmc Serra and it takes forever to refuel pump clicks off continuely like tank is full


you have a bad evap vent solenoid at fuel tank causing fuel tank not to be vented, need to replaced evap vent solenoid, have to purchase from a gm dealer

Sep 03, 2012 | 2005 GMC Sierra

1 Answer

2002 gmc sierra p0171 p0174 p0300 oygen sensor and misfire codes


Check for vacuum leaks to start. Then check the evap system. I just replaced a evap vent solenoid on a suburban with the same codes. fixed the problem.

Apr 17, 2011 | 2002 GMC Sierra 1500

1 Answer

Loolking for code P0445 what does this mean


P0445- EVAP purge control circuit fault!! Check your gas cap, this will cause insufficient vacuum activating the SES indicator. Check the following

a) Absent or tampered fuel cap.

b) De-linked or faulty fuel tank pressure sensor.

c) De-linked, damaged, pinched, or blocked EVAP purge line.

d) De-linked or erroneous EVAP canister purge valve.

e) De-linked or incorrect EVAP vent solenoid.

f) Open ignition feed circuit to the EVAP vent or purge solenoid.

g) Tampered EVAP canister.

h) Leaking fuel sensor assembly O-ring.

i) Leaking fuel tank or fuel filler beck

Sep 29, 2010 | 2008 GMC Sierra 1500

3 Answers

GMC Sierra 06' 4.8 V8. I have a trouble code and nobody has had any knowledge of which part it is that needs to be replaced. DTC P0449 is the code.


DTC P0449 Evaporative Emission (EVAP) vent Solenoid Control Circuit
The vent solenoid is not working properly. The ecm driver could be defective, the wiring could be broken, or the vent solenoid just isn't working.


Sep 18, 2009 | 2006 GMC Sierra 1500 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...