Question about 1999 Saturn SL
These hoses come with a factory clamp which can either be removed with slip joint pliers or a 5/16 socket or flat screwdriver. Once the clamps at both ends are removed then you should work the hose carefully off the fittings. It's sometimes useful just to use a razor knife to cut the hose off the fittings. ( be careful not to cut to deep and damage the plastic neck on the radiator. Once the hose is off just reverse the process, tighten clamps or replace clamps with new hose clamps, top off the radiator with proper coolant.
Posted on Jul 30, 2010
Fairly simple once you have the clamps pulled back
assuming the hoses are seized to the pipes just split them with a razor blade and remove
regardless how much coolant is removed prior to service expect to spill more while removing
after installing hoses and refilling coolant make sure you leave the radiator cap off to bleed the system
Posted on Jul 30, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
May 24, 2017 | Saturn Cars & Trucks
Trace the upper radiator hose to the mounting area on the intake manifold. Loosen the hose clamp on the manifold end of the hose and remove the hose. Pull the thermostat out of the intake manifold.
For more help and troubleshooting go through the help links below:---
Click the link below:-----
THERMOSTAT REMOVAL PROCEDURE/LOCATION DETAILS
Where is Thermostat Located on
How to Replace a Thermostat.
Nov 28, 2012 | Buick Century Cars & Trucks
Oct 31, 2012 | Cars & Trucks
Sep 08, 2011 | 1999 Saturn SL
Dec 23, 2010 | 1999 Saturn SL
Place the bucket under the driver's side corner of the radiator beneath the radiator draincock (located on the bottom of the radiator). Remove the filler cap from the radiator.
Shape a large piece of aluminum foil to form a funnel or channel from beneath the draincock to the bucket, Pinch high side walls in the aluminum foil so it will direct the flowing coolant into the bucket and not allow any to spill on the ground or into the engine.
Turn the draincock clockwise to open it and drain the coolant from your radiator and hoses. Close the draincock when you have finished draining the system.
Locate the thermostat housing. The housing will be on the top of the engine; you can find it easily no matter what model year Saturn you have, by following the main hose coming from the radiator to the engine block. That hose will end at the thermostat housing and there will be one or two houses coming off the housing as well. Disconnect the hoses from the housing.
Using your socket set, remove the bolts holding the thermostat housing in place. Put the tip of your paint scraper between the housing and the engine block and pry up gently to remove the housing. Once the housing is free, remove the gasket that was between the housing and the block. If necessary, use the paint scraper to scrape off any old gasket that is stuck to the metal.
Pull the old thermostat from its seat. The thermostat has a circular steel top with what looks like a raised handle. Simply lift the old thermostat out and place the new one into position.
Lay your new thermostat housing gasket into place and re-install the housing. Tighten the bolts down. Re-connect the hoses and refill your radiator with new coolan
Dec 03, 2010 | 1999 Saturn SL
Nov 21, 2010 | 1999 Saturn SL
Sep 09, 2009 | Saturn SL2 Cars & Trucks
Nov 23, 2008 | 1999 Saturn SL
195 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: