Question about Dodge Dakota

1 Answer

What is the tightening pattern of the intake manifold and torque lbs for a v6 dakota pickup 02.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

Listed below is the 3.7 and 3.9. I'm not sure which engine you have, so I have listed both.



what is the tightening pattern - f7f3c57.jpg

c3bd5e8.jpg

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intake torque on top & bottom bolts


Apply sealer to the lower intake manifold bolts prior to installation. On the 5.0L and 5.7L engines, install the bolts and torque in sequence as follows:
Step 1: 71 inch lbs. (8 Nm).
Step 2: 106 inch lbs. (12 Nm).
Step 3: 11 ft. lbs. (15 Nm).


12_23_2011_2_54_59_am.gif

Fig. Lower intake manifold bolt tightening sequence-5.0L and 5.7L engines / zoom image link here

Upper intake manifold mounting bolts/studs, torque in a crisscross pattern as follows:
  1. Step 1: Torque the bolts/studs to 44 inch lbs. (5 Nm).
  2. Step 2: Torque the bolts/studs to 83 inch lbs. (10 Nm).

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day and Merry X-mas.

Dec 23, 2011 | 1999 Chevrolet Tahoe

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

Looking for cylinder head torque specs and intake manifold torque specs


on the 2.5 4 cylinder

step 1 18 ft lbs.

step 2 26 ft lbs. except bolt #9 re tighten it to 18 ft. lbs.

step 3 all bolts an additional 90 degrees.

intake manifold bolts 65 ft lbs.

on the 3.3L V6

step 1 35 ft lbs.

step 2 tighten all bolts an additional 130 degrees

step 3 tighten center 4 bolts an additional 30 degrees

intake manifold bolts 88 in. lbs.


Jan 13, 2011 | 1992 Buick Century

2 Answers

02 Chevy avalanche 1500 need to know torque specs for intake manifold and if theres an tightening sequencing


the torque specs for your intake are the first pass to 44in/lb the second pass to 89in/lb. and the tightening sequence is as follows:
start on the passenger side (right side) the 3rd bolt (from front) is #1 then on the driver side (left side) 3rd bolt is #2 and 4th bolt is #3.Back to right side 2nd bolt is #4 and 4th bolt is #5. Left side 2nd bolt is #6 and 1st bolt is #7. Right side 5th bolt or rear most bolt is #8, left side rear bolt is #9. Then finish with right side 1st bolt is # 10.

Do that the first time at 44 in/lb then same thing over again at 89 in/lb

Nov 27, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

What are the torque specifications for the intake manifold on a 2003 Ford F150 4.2 liter engine?


These torque specs are from the Haynes manual (Ford pick-ups 97' - 03') This is a 2- step proccess. step-1 44-in-lbs step-2 89-in-lbs. There are 14 bolts that hold the manifold in place, tightening sequence goes as follows: start from the center( WORK IN A "X" PATTERN)

Oct 02, 2010 | 2003 Ford F150 Regular Cab

1 Answer

Intake manifold torque spec


The Intake Bolt Torque...

Tighten in 3 steps: Step 1: 7.5 FT Lbs Step 2: 15 FT Lbs Step 3: 24 FT Lbs(to torque bolts & nuts, start in center using crisscross pattern)

Hope helps (remember to rate and comment this).

Sep 12, 2010 | 1998 Ford Mustang

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

What pattern should i use to tighten the intake manifold bolts on a 2005 lincoln LS


V6 or V8? Start with the middle right side,then across to the left,then
from one diagnal corner to the opposite side,and vice versa,till they are
all snug. I'd recommend using a torque wrench and getting the proper
torque values when doing head,and or intake manifold work,just to be
safe, but an estimated 50ft. lbs. should be pretty sufficient.
You might be able to get the specs in a Chilton's manual. Good luck.

Mar 31, 2010 | 2005 Lincoln LS

2 Answers

Torque Specs for Head Bolts on 1997 GMC Sierra V8 5.0 Vortec?


.0L Torque Specs Belhousing to engine bolts 28-38 ft/lbs Camshaft sprocket bolt 40-45 ft/lbs Camshaft thrust plate to engine block bolts 108-144 in/lbs Crankshaft pulley to vibration damper bolts 35-50 ft/lbs Cylinder head bolts -1979-1992 --Step 1 55-65 ft/lbs --Step 2 65-72 ft/lbs -1993-up --Step 1 25-35 ft/lbs --Step 2 45-55 ft/lbs --Step 3 75-85 ft/lbs Differential shaft lock bolt 15-30 ft/lbs Driveshaft U-joint to pinion flange bolts 70-95 ft/lbs Exhaust manifold bolts 26-32 ft/lbs Flywheel mounting bolts 75-85 ft/lbs Front engine mount nuts 72-98 ft/lbs Intake manifold to head bolts --Step 1 96 in/lbs --Step 2 16ft/lbs --Step 3 23-25 ft/lbs Intake manifold (upper intake to lower) 12-18 ft/lbs Oil filter insert to engine block adapter bolt 20-30 ft/lbs Oil pan mounting bolts -1979 --Step 1 (Large bolts) 11-13 ft/lbs --Step 1 (Short bolts) 7-9 ft/lbs --Step 2 (Large Bolts) 15-17 ft/lbs --Step 2 (Short Bolts) 10-12 ft/lbs -1980 to 1987 9-11 ft/lbs -1988 to 1993 6-9 ft/lbs -1994-up 110-144 in/lbs Oil pickup tube to main bearing cap nut 22-32 ft/lbs Oil pickup tube to oil pump bolts -1979 to 1987 10-15 ft/lbs -1988-up 12-18 ft/lbs Oil pump mounting bolts 22-32 ft/lbs Pinion bearing preload 8-14 in/lbs Pressure plate to flywheel bolts 12-24 ft/lbs Rocker arm fulcrm bolts 18-25 ft/lbs Spark plugs 7-14 ft/lbs Timing chain cover bolts 12-18 ft/lbs Vibration damper to crackshaft bolt 110-130 ft/lbs Wheel lug nuts 85-105 ft/lbs

Mar 16, 2010 | Chevrolet C1500 Cars & Trucks

1 Answer

Looking for the torque specs for 1998 chevy astro van?


1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Dec 28, 2008 | 1998 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...