Question about 1994 Chevrolet G20

1 Answer

Power window How do you relace the power window motor on a 1995 g20 van

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers


REMOVAL & INSTALLATION
R/V Series

  1. Raise the glass to the full up position and tape it to the door frame with fabric tape.
  2. Disconnect the negative battery cable.
  3. Remove the door trim panel.
  4. Remove the window control bolts and lay the control aside for access.
  5. Remove the regulator-to-door panel attaching bolts.
  6. Disconnect the harness from the regulator.
  7. Slide the regulator assembly rearward, disengaging the rollers from the sash panel.
A notch is provided in the sash panel to allow disengagement of the forward roller on the window regulator.
  1. Remove the regulator assembly through the access hole in the door.

CAUTION The next step must be performed when the regulator is removed from the door. The regulator lift arms are under tension from the counterbalance spring and can cause serious injury if the motor is removed without locking the sector gear in position.
  1. Drill a hole through the regulator sector gear and back plate. DO NOT drill a hole closer than 1 / 2 in. (13mm) to the edge of the sector gear or back plate. Install a pan head sheet metal tapping screw (No. 10-12× 3 / 4 in.) in the drilled hole to lock the sector gear in position.
  2. Remove the motor-to-regulator attaching screws and remove the motor from the regulator.
To install:
  1. Prior to installation, lubricate the motor drive gear and regulator sector teeth.
  2. Install the motor to the regulator. Make sure the motor and sector gear teeth mesh properly before installing the retaining screws.
  3. Remove the screw locking the sector gear in the fixed position.
  4. Reposition the motor in the door and install the wiring connector.
  5. Attach the regulator to the door.
C/K Series
  1. Disconnect the battery ground cable.
  2. Remove the door trim panel.
  3. Remove the water deflector by peeling it back.
  4. Disconnect the door lock rods at the module.
  5. Loosen the upper run channel bolt.
  6. Move the run channel away from the glass.
  7. Pull the wiring harness towards the door to reach the connector. Remove the boot from the wiring and disconnect the harness at the door hinge pillar.
  8. Remove the module and window assembly from the door frame by tilting it and lowering it from the door.
  9. Fold back the tab on the channel and slide the glass out.
  10. On trucks with power components, drill out the rivets from the inner handle housing.
  11. Drill out the regulator assembly rivets.
  12. Remove the regulator/motor assembly.

CAUTION The next step must be performed when the regulator is removed from the door. The regulator lift arms are under tension from the counterbalance spring and can cause serious injury if the motor is removed without locking the sector gear in position.
  1. Install a pan head sheet metal tapping screw through the sector gear and backing plate in the hole provided, to lock the sector gear in position.
  2. Drill out the motor-to-regulator attaching rivets and remove the motor from the regulator.

To install:
  1. Prior to installation, lubricate the motor drive gear and regulator sector teeth.
  2. Install the motor to the regulator. Make sure the motor and sector gear teeth mesh properly before installing the replacement attaching bolts and nuts.
  3. Remove the screw locking the sector gear in the fixed position.
  4. Reposition the motor/regulator in the door and install the wiring connector.
  5. Attach the regulator to the door.
  6. Slide the glass out into the channel and fold over the tab.
  7. Fit the glass into the rear channel in the door, then, while pulling the channel towards the glass, fit the glass into the front run channel.
  8. Install the boot from the wiring and connect the harness at the door hinge pillar.
  9. Install the lower run channel bolt.
  10. Install the door lock rods at the module.
  11. Install the module panel screws, starting at the top left, then the top right.
  12. Install the water deflector.
  13. Tighten the upper run channel bolt.
  14. Install the trim panel on the door.

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat or air not blowing out of any vents in my 95 Chevy g20 van


the heater control valve might be broken or plugged

Dec 11, 2016 | 1995 Chevrolet G20

1 Answer

My 95 Chevy g20 van will not blow heat or air from any vent


I would recheck to make sure that control switches are hooked up. other than that you could check to make sure your air ducts are connected.

Dec 10, 2016 | 1995 Chevrolet G20

1 Answer

Exactly where under the hood of a '95 Chevy G20, van do you disconnect the rear ABS PUMP?


The ABS module is not under the hood.It is under the van floor on the passenger side at about the middle of the van.Slide under the Van at the passenger side cargo door and look up.

Feb 27, 2015 | 1995 Chevrolet G20

1 Answer

1995 g20 van wiper motor works fine but park position sometimes stops halfway ,wiper transmission fine


Jimmy, the 1995 gm used a delay circut board for the wipers.these are known to fail, gm even had a recall to fix this. I dont know if they will still repair this free. the board is available from dorman parts and located on the wiper motor under the plastic cover. It is a fairly esay fix. Hope this helps, Bill

Mar 28, 2013 | 1995 Chevrolet G20

1 Answer

Sparks jumping from spark plug wires in 1995 chevy g20 van the wires are new and so are the plugs cap and rotor and coil


replace the leads with a heavier grade of lead insulation Use spacer bars to seperate the leads as the current will jump to the lead of lower resistance ( ie piston not in compression mode). Spark jumping will cause problems not the least being a blown motor through firing at the wrong time

Jan 06, 2013 | 1995 Chevrolet G20

1 Answer

How do I remove or replace the arm rest on my Captains chair? I have a 1995 Chevy G20 van.


how do i remove the broken piece of arm rest from my 1999 full size chevy van . front drivers seat

Jan 24, 2011 | 1995 Chevrolet G20

1 Answer

How do you remove wiper motor from 1995 full size G20 van


take the dog house out. its not a fun job.

Sep 07, 2010 | 1995 Chevrolet G20

1 Answer

Wiper problem


Are you sure that it is the board?? I have a 1995 c1500 and it was doing same thing. Its mounted on rubber gromets and developed a bad ground. Take a wire with two big clips on both ends of it and clip one to the wiper motor. And other on the motor, on a bolt or something.

May 06, 2010 | 1995 Chevrolet G20

2 Answers

Where is the jack stored on our 1995 Chevy G20 van


It should be located on the right hand side fender wall on most Chevrolet / GMC Vans. Another location it may be under your hood on one of the fender walls (these is more common with Dodge)

Aug 23, 2009 | 1995 Chevrolet G20

1 Answer

1995 G20 van


the actual power window motor is getting old and probably needs replacement. as they age they get slower and picky about which way they want to go, outside temp also affects the operation also. in warmer weather they tend to work better

Aug 07, 2008 | 1995 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

1,378 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...