Question about 1998 Buick Park Avenue

3 Answers

How to connect da spark plug wires in the right order

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Buick Master
  • 81,294 Answers

If u already have them off just follow the diagram below.

how to connect da spark plug wires in the right - 8f4c97d.gif

Posted on Jul 29, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 2,100 Answers

Usually you take them off one at a time and match them up, If you have them all off, you need to get the firing order and the location of the Number one coil, the number one piston is always the front most cylinder,

http://autoforums.carjunky.com/Automotive_Repair_C1/Engine_Troubles_F16/need_firing_order_for_98_buick_p.

Check it out.

Posted on Jul 29, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

The coils and the intake is number if the coils re original
'the number for eack cylinder is above each plus on the intake

Posted on Jul 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the Wire Order with distributor?


theres no distributor and the firing order for your 3.8 is 1-6-5-4-3-2-the following link shows the coil pack
Buick General Motor 3800 V6 Engine Firing Order DIS IDI ignition timing 3.8 Buick Engine Coil Pack Firing Order Spark Plug Wire Location Which way do the spark plug wires go on & what cylinder is what?
.
For the Buick V6 231 3.8 liter turbocharged engine:
.
Answers!
.
Firing order:
1 - 6 - 5 - 4 - 3 - 2.
.
Spark plug wire location on coil pack:
.
Closest to the back of the car, left to right: 1 - 5 - 3.
Closest to the front of the car, left to right: 4 - 2 - 6.
.
Spark plug wire location on engine:
.
drivers side, front to back of car: 1 - 3 - 5.
passenger side, front to back of car: 2 - 4 - 6.
.----and this link shows the coil pack to cylinders
.
3 8 Buick Turbo Engine Coil Pack Firing Order Spark Plug Wire Location

Aug 15, 2015 | 1987 Buick Regal

1 Answer

How to replace freeze plug on 1998 dodge ram pickup


Use your crescent wrench to disconnect the positive and negative battery cables. Be careful not to touch both battery posts together with your wrench, as this will damage the battery and possibly harm you.

Use your spark plug socket to gently grab the insulated end of the spark plug wire; pull it away from the tip of the plug. The spark plug socket looks like a regular set of pliers, except that the jaws have rubber inserts to grip the insulation without damaging it. The plug wire itself looks like a 15-gauge wire with a rubber boot on each end: One end is connected to the spark plug present in each of the eight cylinders, while the other end is connected to a coil pack terminal, usually located on the right rear side of the engine compartment. The coil pack is a square, black, solid-state component that has eight terminals for each of the eight plug wires.

Use your spark plug socket to gently pull the coil pack end of the plug wire away from the terminal. Repeat the last two steps until all eight wires are removed.

Consult the service manual for your vehicle's year model and determine the exact firing order. You will need to connect each new wire to the numbered coil pack terminal and the corresponding engine cylinder. Failure to replace the wires in the right order will result in failure of engine operation.

Use your crescent wrench to reconnect the battery cables (black wire to black terminal, red wires to red terminal).

Start the vehicle and make sure it is running smoothly. If you hear misfiring in the engine, use the spark plug wrench to make sure all the connections are properly seated. If the condition continues, you will need to further diagnose the electrical system.

Jul 15, 2012 | 1998 Dodge Ram

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

1 Answer

What are the numbers on a distributing cap


engines have a fireing order for each piston like 18436572 for an eight cylinder the distributer cap will have eight spark plug wire connections starting with number one connect plug wire to number one cylinder then moveing clockwise around the capconnect plug wire to the number eight cylinder untill all wires are connected in order to the right cylinder

Feb 16, 2010 | 1989 Saab 9000

2 Answers

Number 1 spark plug for 2000 Mazda MPV


The cylinder order is 1,2,3 (rear row, left-to-right) and then 4,5,6 (front row, left-to-right).
When replacing spark plug wires or plugs, it's very helpful to do one at a time to avoid connecting them incorrectly.
Hope this helps, Sherwin

Dec 29, 2009 | 2000 Mazda MPV

1 Answer

Change plugs and wire and engine will not acclerate. This is a built 350 short block chevy with pro charger.


350 Chevy engine in what? 1990 Corvette? Who built it, did you?

Sounds as though you have plug wires wrong.
Firing order is 1-8-4-3-6-5-7-2

Distributor Ignition System:
Distributor rotates Clockwise. (Rotor)
Find Number 1 tower on distributor cap, go Clockwise with Firing Order.

Distributorless Ignition System:
VIEWING the engine from the Front of the car.

Spark plug wire connections along the back, starting from Left side going to Right side;
2-3-7-4

Spark plug wire connection towards the Front of the engine;
6-1-5-8

(To guess I would say you have 5 and 7 wires switched)

Left side cylinder order is 1-3-5-7, going from front to back.
Drivers side is Left side.
Right side cylinder order is 2-4-6-8, going from front to back.

Oct 13, 2009 | 1990 Chevrolet Corvette

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

2 Answers

Changing spark plugs on lincoln town car


Remove the spark plug wires, remove the spark plugs,replace them. Do this one cylinder at a time if you never did it. On that year you may need to remove the upper intake to access the plugs on one side. In that case go to a shop. This would not be a novice job.

Jun 28, 2009 | 1998 Lincoln Town Car

2 Answers

Daewoo Lanos Ignition Wire Order


spark wire order of daewoo lanos is 1423 with you facing the engine; spark 1 is on th extreme left then 2,3,4 ..insert them as 1 (extreme left) is the highest to be plugged in, under which insert 4 then 2 then 3 at the bottom, hope it helps

Feb 27, 2009 | 1999 Daewoo Lanos

2 Answers

Ihave changed the spark plugs but i dont know if put the caps in


Not sure what you're asking. The only order that matters is the order of the spark plug wires. There isn't an order for the spark plugs themselves. So are u looking for the order of the spark plug wires?

Nov 12, 2008 | Honda Civic Cars & Trucks

Not finding what you are looking for?
1998 Buick Park Avenue Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...