Question about 1997 Isuzu Trooper

1 Answer

HOWDO I REMOVE MY FRONT ROTORS - 1997 Isuzu Trooper

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 277 Answers

Most automobile front are floating. I believe yours are.
They collect dust, and they rust on, so... take a heavy hammer and give it a really good hit. Now make sure that the truck is well supported.
Two hits, should make it frree.

Posted on Jul 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Howdo i remove the shifter knob on my 91rs??


If its a stick with a stock ball head it should just unscrew.

If its a automatic with the leather covered ball head it will
either depending on year have a staple in the front lower part of the ball or you have to remove the release cap on top of
the ball and take out the snap ring then pull it off.

Jun 14, 2016 | Cars & Trucks

1 Answer

Remove the front rotor


Take the brake caliper bolt and try tightening it against the rotor and then back it off. Turn the rotor, tighten, then back it off and repeat this until the rotor pops loose.

Nov 01, 2012 | Cars & Trucks

1 Answer

How do you remove front brake rotors


remove tire. remove caliper bolts, hang caliper out of the way. Remove caliper support bracket. cut or pry off rotor securing ring from one wheel stud. wiggle off rotor...rubber mallet may be needed if rust is present.

May 20, 2010 | 2004 Toyota Corolla

2 Answers

How to remove the rotor on a navigator?


front or rear brake rotor? b sure to shut off the air ride system! the switch is located in the rear kick panel! lift and support front remove tires !the caliper has two mounting bolts remove those and hang caliper to the side using a metal coat hanger! now look at the bracket that was connected to the caliper remove those two bolts !the rotor should come off

Mar 16, 2010 | 2001 Lincoln Navigator

1 Answer

How to replace 99 gmc 3/4 tom brake rotors


Removal & Installation
  1. Remove 2/3of the brake fluid from the master cylinder.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Remove the front wheel hub extension (dual wheel vehicles only).
    • Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the rotor from turning.
    • Mark the relationship of the front wheel hub extension to the hub
    • Remove the front wheel hub extension bolts
    • Remove the front wheel hub extension from the vehicle. It may be necessary to tap around the perimeter of the hub extension with a rubber mallet to loosen it from the hub
  5. Mark the relationship of the rotor to the hub.
  6. Remove the caliper and mounting bracket as an assembly.
  7. Hang the caliper and the mounting bracket assembly from the suspension using mechanics wire.
  8. Remove the rotor.
  9. If the rotor is difficult to remove due to corrosion in the hub area use the following procedure to remove the rotor (25 series only).
    • Clean all the surface areas and the threaded holes of contamination
    • Generously apply penetrating oil or the equivalent to the hub/rotor area
    • Insert (2) M10 x 1.5 bolts (jack screws) into the threaded holes of the rotor
    • Tighten both bolts evenly to force the rotor from the hub.
c3692a2.gif
To install:
  1. Clean all rust and contaminants from the both side of the rotor and the hub flange.
    NOTE If the rotor was removed using the jack screw method you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

  2. Install the rotor.
  3. Install the caliper and the mounting bracket as an assembly.
  4. Install the tire and wheel assembly.
  5. Remove the safety stands.
  6. Lower the vehicle.

Oct 25, 2009 | 1999 GMC Sierra

2 Answers

Wheels bearing stuck rotors wont come off. Howdo Iget them off?


I hope you ready for some fun. I just did mine on the same car. first off DO NOT listen to the idiots on the internet. They are stuck for a reason. you can't just pull them off. unless you can bench press 4000 lbs. that is!!! you need to remove upper ball joints lower ball joints then steering arm. the whole hub assembly will then come off. this is assuming you already took the 36mm axle nut off. next remove the 4 bolts on the rear wheel bearing assembly. and take in to machine shop they will have to press out bearings so that you can replace your rotors. as long as your doing that you might as well have them put in new bearings at the same time. this is not a job you want to do again anytime soon. also I replaced the lower ball joints because my were somewhat bad. I am saving you a big headache here. they charged me 20 bucks per side for pressing bearings in and out and 20 more for pressing new ball joints in and out. new bearings cost me 40 per side. so all in all it cost me 300 bucks for everything. but at a shop ( I've already checked) this is a $750 job. Have fun!!!! At least you know you'll be saving money. by the way. the front axle nut is a 36mm torqued to 180ft.lbs. for your info. also wheel torque is 81 ft lbs.









Jul 09, 2009 | 1995 Honda Accord

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

3 Answers

2006 subaru legacy remove front brake rotor


Hello, hope this info helps...(subytech1)...



REMOVAL
15-INCH TYPE

  1. Lift-up the vehicle, and remove the front wheels.
120334720


  1. Remove the caliper body and the support from housing, and suspend it from strut using a wire.
120334721


  1. Remove the disc rotor. NOTE: If the disc rotor seizes up within hub, drive the disc rotor out by pushing with an 8 mm bolt in holes B on the rotor.
  2. Clean mud and foreign particles from the caliper body assembly and the support. 16-INCH TYPE Refer to 15-inch type. 17-INCH TYPE Refer to 15-inch type.
INSTALLATION

  1. Install the disc rotor.
  2. Install the caliper body and the support to housing. Tightening torque: 80 Nm (8.2 kgf-m, 59 ft. lbs.)
  3. Install the front wheels.

Mar 27, 2009 | 2006 Subaru Impreza

1 Answer

1998 honda civic front rotor replacement


Varvah, front rotor: Jack up the car, put on safety stands, remove wheel, remove caliper mounting bolts (2), hang caliper in place w/ bungy cord, rope, etc. so you don't stress the brake line, remove caliper mounting bracket bolts, remove bracket from rotor, remove retaining screws on the front of the rotor, remove rotor. If it's stuck, get 2 - 8x 1.25 mm screws (longer version of what u removed), tighten them in the rotor, they will push it off easily. Reverse to install, tighten bracket to 80 ft lbs, caliper to 20 ft lbs. Let me know if u need more info. Countrycurt0

Oct 09, 2008 | 1998 Honda Civic

Not finding what you are looking for?
1997 Isuzu Trooper Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...