Question about 2000 Mercury Villager

1 Answer

How do you install a camshaft position senor for a 2000 mercury villager van

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

The camshaft sensor is part of the distributor. Not serviceable separately.
What is the issue?

Go here for help

http://groups.yahoo.com/group/villagerquest/

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft pisition sensor for 1995 mercury villager


1995 Mercury Truck Villager Van 3.0L EFI SOHC 6cyl

The Crankshaft Position Sensor is located: Under hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block.

Jul 22, 2015 | Mercury Cars & Trucks

2 Answers

Code 0300 2000 Mercury Villager


Camshaft position sensor causing random misfire. Stuck EGR valve or clogged EGR ports.

Please comment on my info.

Mar 30, 2013 | 2000 Mercury Villager

1 Answer

How do I activate my alarm system on my mercury villager mini-van?


It is an automatic system, so if it is not working you have a defective part. The system control module needs to be scanned to see what the problem might be and then diagnosed based on what shows on the scan.

Jun 15, 2012 | 2000 Mercury Villager

1 Answer

We have a 1999 Mercury Villager which will not run more than ten minutes. We replaced the throttle position sensor,fuel filter and have ran injector cleaner through it with no improvement at all.


Check the codes, you should find that you need to replace the crankshaft position sensor and/or the camshaft position sensor. You can take it to most auto parts stores and they will put it on a meter and run the code test for you.

Jul 30, 2011 | 1999 Mercury Villager

1 Answer

Looking for location of crankshaft position sensor on 2000 mercury villager with 3.3l engine. parts store says there are 2 per vehicle. found one at front of engine. any idea where the 2nd one would be?


The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing The bottom of the sensor is positioned next to the drive plate. Remove the 10mm bolt holding the sensor in place and remove the sensor. Install the new crankshaft sensor.
Install crankshaft sensor bolt and tighten. Connect wiring. merry christmas !!

Dec 25, 2010 | 2000 Mercury Villager

2 Answers

Lost remote to disable alarm on 2000 mercury villager how can i disable it and start my van


If you have the factory alarm system, you can put your key into either door and lock and unlock the door, that signals the computer to deativate the alarm. If you have an aftermarket alarm system installed, it will have to be removed and the wiring that the alarm ties into must be restored to factory design.

Apr 23, 2010 | 2000 Mercury Villager

2 Answers

1997 Mercury Villager car will turn over, but will not start. Used ether but nothing. Can't get spark. Installed another coil-- nothing. Installed electonic ignition module--nothing. Any ideas???


if you can get a scan tool, hook it up and check to see if you are getting engine RPM while cranking. if not than you may have faulty cranck sensor.

Nov 26, 2009 | Mercury Villager Cars & Trucks

2 Answers

2000 mercury villager wont start


Check your inertia switch. This is usually located in the rear interior of the vehicle. It has a reset switch you hold for 3 seconds. It is a safety switch to kill the fuelpump in an accident. Can trip with door closings.

Aug 16, 2009 | 2000 Mercury Villager

Not finding what you are looking for?
2000 Mercury Villager Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...