Question about 1999 Oldsmobile Alero

1 Answer

My car is overhit,the thermo in new,the bleed is than but stil overhit

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 14,036 Answers

OVER HEATING AT A STANDSTILL PROBABLY COOLANT FAN NOT COMING ON.CHECK COOLANT FAN FUSE/RELAY.IF BOTH GOOD COOLANT TEMPERATURE SENSOR FAULTY.HOT WIRE COOLANT FAN.NO RUN REPLACE COOLANT FAN MOTOR.IF FAN MOTOR RUN.FAULT IN FAN MOTOR WIRE CONNECTOR.IF ALL IS GOOD YOU COULD HAVE A LEAKING HEAD GASKET.CHECK ENGINE OIL LOOK LIKE MILK SHAKE HEAD GASKET BLOWN.

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi,my powersteering pump is making a whining sound so i changed it with a new one and ,i was doing everything by book but stil the same problem, can somebody give advice? Polo classic 16i 98model


at www.reliable-store.com info that cover everything from wiring diagrams, electrical diag, fault/error codes, troubleshooting, service/repair/operation/maintenance info, PCV, etc.
that'll be all you need, without doubt.

Apr 11, 2018 | Cars & Trucks

1 Answer

Engine overhiting ml 320 cdi


remove thermostat with cold engine assembly again check the belt fit new radiator cup blead your sistem and drive 1/2 hur ef stil over heating you have radiator blockige.

Aug 14, 2012 | Mercedes-Benz ML320 Cars & Trucks

1 Answer

Why is my volvo 240 tempeture gage running over half and not preasureizing,its got new rad new thermo,new water pump?


bleed the air out.turn your heating on full to bleed the air from your heating remove the cap from your expansion bottle to do that.

Mar 22, 2012 | 1982 Volvo 240 Series

2 Answers

Spongy breaks after bleeding on a 1997 ford expedition


the is still air in the system, rebleed the brakes starting with the- right rear-left rear- right front- left front. some vehicles with ABS need to be running so the abs system gets bleed properly.

Feb 24, 2012 | 1997 Ford Expedition

1 Answer

Where is the thermostat located on a 1993 olds cutless supreme 3.1 liter engine How to install a new one


if you follow the upper radiator hose to where it connects to the engine. drain anti freeze a
little(to get below hose,remove hose from thermostat housing,remove 2 bolts & remove housing
the thermostat will pull out.make sure you install the same way(spring end toward engine)
if new thermo has a small hole in it(some do)make sure its up 12 o'clock position.
reconnect & refill system.there are air bleeders in system 1 at thermo housing & possibly
1 around the water pump.after car is running you need to open bleeder to allow trapped
air out.CAR WILL OVER HEAT IF ITS NOT BLED
top off system after bleeding

good luck

Jun 17, 2011 | 1993 Oldsmobile Cutlass Supreme

2 Answers

My volvo s70 break pedal goes all the way to the floor ad new master cilinder new bled nipals stil after 2week its gone back down again what do i do next


It sounds like you have a small brake fluid leak, allowing air to enter the system. Small leaks can be hard to find. You will have to remove the wheels in order to inspect the calipers. Also make sure the bleeder valves are tightened securely after bleeding the brakes. Did you bleed the master cylinder when you first installed it? If you can't find a leak, bleed the entire system again, including he master cylinder.

Feb 15, 2011 | Volvo S70 Cars & Trucks

1 Answer

97 vw jetta overhiting new water pump new thermostat new head gasket & steal overhiting


Did you burp the air out of the cooling system once you were done reassembling the car? If not, click my screenname, go to my tips and tricks, and follow the procedure I posted there.

Feb 03, 2010 | 1997 Volkswagen Jetta

3 Answers

97 jetta gt 2.0 overheating


if the coolant is full and all the air is bleed out of the cooling system make sure the cooling fans turn on if not then check the relays and fuses and wiring. and if thats ok then use a block tester to check for a combustion leak. you can get a block tester for a parts store you simply install it in place of the radiator cap and run the car the chemical in the block tester will change color from blue to yellow if there is a combustion leak.

Mar 16, 2009 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1999 Oldsmobile Alero Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...