Question about 1999 Ford Econoline

1 Answer

Forward blower not working - 1999 Ford Econoline

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Unplug the the 2 wire plug on the blower and attach a wire from the post on the blower that the black wire went to the the body (ground it) attach another wire to the other post on the blower and touch to hot post of battery if the blower comes on check your relay or switch.NOTE BE SURE THE TWO WIRES YOU CONNECT TO THE POSTS IN THE BLOWER DO NOT TOUCH EACH OTHER!

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Heater blower works only on high speed


Very common problem. The Blower Motor Resistor is burned up. It is located in the bottom of the Heater/ A/C Housing just to the left and forward of the blower motor It is secured by 3 screws (One of which is a real "blankety-blank" to get to.) The resistor is available at most parts stores for around $30. I recommend using the replacement made by Borg Warner (BWD) It is made completely differently from the original. (You will see the difference just by looking at it.) I have never had one of these come back with the same problem. (Although I have had several of the OEM resistors come back on me.)

Jan 30, 2011 | 2001 GMC Jimmy

2 Answers

I have a 2000 grand prix 3.8 with heater problems. i have changed the heater core, thermostat, resister, blower, the 2 relay switches and heater fan. there still is very little air coming thru.. any...


The blend door may not be working properly. It is actuated by a vacuum motor.

or the following part may be bad:

Blower Motor Control Module Removal & Installation To Remove:
  1. Remove the insulator from the right side of the instrument panel.
  2. Disconnect the connectors from the blower motor resistor and blower motor.
  3. Loosen the two forward screws and remove the rear screw of the resistor assembly.
  4. Remove the blower motor resistor assembly.
To Install:
Install the blower motor resistor assembly. Install the rear screw and tighten the forward screws. Connect the electrical connectors to the blower motor and resistor assembly. Install the insulator under the right side of the instrument panel.
prev.gif next.gif

Jan 21, 2011 | 2000 Pontiac Grand Prix

1 Answer

REPLACED BLOWER MOTOR CONTROL MODULE...Now blower is working but not very much air flowing out of vents! Fan speed is working...it heat and cools. but still not adequate air flow from the vents ..2000...


check your blower hoses to see if one or more have come loose or got redirected or the selector switch isn't functioning properly (is it blowing better on defrost as opposed to floor vents, or forward vents, etc.)
Good luck

Oct 26, 2010 | 2000 Jeep Grand Cherokee

3 Answers

The fan motor switch will not work on positions 1,2,3- but do work on 4 and 5.. What needs to be replaced or repaired


replace your blower resister it location in on you blower motor box it will be behind you glove box I think ,but replace it all will be ok.I hope this These are a pain to reach. They are bolted under the dash forward of the the blower motor. If you pull the blower motor out first, you can see the bolts that hold the resistor in. They usually melt the resistors on the circuit board. Good luck. 79131833.gif ,

Nov 22, 2009 | 2001 Pontiac Grand Prix

1 Answer

Instructions for installing a resistor for the blower motor on a 2001 pontiac gran prix


Its a straight forward job, the blower resistor is to the left of the blower motor and will have 2 screws holding it in. The blower is just above the passengers feet.

Nov 20, 2009 | 2001 Pontiac Grand Prix

1 Answer

01 dodge caravan has heater blower that will not work until the van is up to highway speed.


Does the blower actually start working at speed, or are you merely getting air flow due to your forward motion? Check the fuse for the blower, and the switch. Use a test light to see if you are getting power to the blower motor. Is the ground connection for the motor clean and tight? If you have power, the blower motor may be defective, or something blocking it from spinning.

Nov 06, 2009 | 2004 Dodge Stratus

1 Answer

Air and heat wont work unless blower is on high, where do i find the regulator to change it


Sound like the blower motor resistor is bad.

Blower Motor Control Module Removal & Installation To Remove:
  1. Remove the insulator from the right side of the instrument panel.
  2. Disconnect the connectors from the blower motor resistor and blower motor.
  3. Loosen the two forward screws and remove the rear screw of the resistor assembly.
  4. Remove the blower motor resistor assembly.
To Install:
  1. Install the blower motor resistor assembly.
  2. Install the rear screw and tighten the forward screws.
  3. Connect the electrical connectors to the blower motor and resistor assembly.
  4. Install the insulator under the right side of the instrument panel.

Jun 24, 2009 | 1998 Buick Century

1 Answer

Blower motor quit working


Fuse will be under dash drivers side. it's easy to check power at motor with a vom just remove the single wire from blower and attach positive to that wire and negative to a good ground. turn key on and check reading with switch in all positions. If nothing probably a fuse are the resisters in the duck forward of the blower that controls speed. If you have power to blower, then of course bad blower and maybe so anyway if it blew the fuse. It may be fixing to quit. I can supply you with a schematic if you want?

Dec 14, 2008 | 1995 Ford Escort

1 Answer

Switch on heater is not working


it pops out forward. put a slim blade screwdriver or knife behind the edge and prise it forward

Oct 18, 2008 | 1999 Mazda 626

Not finding what you are looking for?
1999 Ford Econoline Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...