Question about 1966 Ford Mustang

Open Question

Why does my 1966 mustang shut off when it gains spead or on turns?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
yotaguy
  • 232 Answers

SOURCE: 1966 mustang will not shift up when driving.

The transmission probably needs a basic maintenance,try changing the transmission filter and fluid,this may clear the problem right up.Check the fluid t see if its a reddish brown color and cloudy,if it is its time to be changed.

Posted on May 17, 2009

Ad
  • 5 Answers

SOURCE: how remove 1966 Ford Mustang 200 cu.in 6-cyl. crankshaft pulley

Hi,
You can remove that center bolt easily with an impact gun. It has normal threads on it. An impact gun will prove to be an affordable tool that you will use again. You can get an electric one from Harbor Freight. They make the job of removing tough bolts much easier. If the engine is in the car, you might not have enough room. You can use a ratchet and if the engine is turning, you can hold the pulley with another tool sold at Harbor Freight called a rubber strap wrench.

Posted on Dec 06, 2009

Testimonial: "Will report again when the job is done. Thanks for this info: 1) Center bolt is normal thread 2) Tools can be pruchased at Harbor Freight"

drsinister69
  • 2317 Answers

SOURCE: 1966 Mustang I6 starting problem

Sounds like the fuel pump, clogged fuel filter, or a stuck needle and seat in the carburator.

Posted on May 02, 2010

ZJLimited
  • 17970 Answers

SOURCE: firing order for 1966 ford mustang 200 cubic inch

The engine is a 200 CID straight six, the firing order is 153624...

21a4dc6.jpg

Just pop the distributor cap and have someone crank the engine while you watch the rotor.

How I can determine which hole in the distributor is assigned to the #1 plug wire.
Pull the number one plug. Turn the engine over slowly (with a wrench) while holding your finger over the plug hole. When the air builds (a lot of) pressure you are coming up to the number one spot on the distributor. (the rotor will point to the location of the #1 hole in the distributor.)

Quick methods to disable the engine I have seen people do on the classics:
Close the points by loosening the set screw
Pull the rotor cap
Connect a wire from the coil to ground. (effectively closes the points. Can damage the coil if key is left on.)
Pull the main ignition wire
And there are some tricks at the starter solonoid involving the ballast resistor bypass that is used to provide a hotter spark while cranking. (Two little wires at the starter solonoid - one is crank the other is the ballast bypass.)

Might give those a look-see. Best of luck (rememeber rated this help).

Posted on May 17, 2010

Testimonial: "This has been very helpful!! Thank you!"

SOURCE: Wiring diagram 1966 Mustang

I would search the internet for it. That's the only advice I can give you for now. Also when searching put in Wiring Schematics instead of diagram.

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1966 Ford Mustang had heater core and motor replaced. No air comes out of vents when it is turned on.


Have you checked to see if wiring is reconnected to the blower motor, and if you have power there, if not, check the fuse.

May 16, 2015 | 1966 Ford Mustang

1 Answer

Brake light and turn signal


check for power at or near socket. Maybe the socket has lost continuity. recommend replacement

Mar 19, 2014 | 1966 Ford Mustang

1 Answer

Why is it that my 1966 ford mustang is not holding a charge after replacing the alternator and short circiut relay


THE 1966 FORD MUSTANG YOU HAVE EXTERNAL FIELD RELAY ITS AIR GAP IS .015 POINT GAP .020. VOLTS TO CLOSE 2.5 VOLTS THE VOLTAGE REGULATOR AIR GAP .049 - .056 POINT GAP .017 - .022 VOLTS AT 125 DEGREES TEMPERATURE IS 13.8 - 14.4 VOLTS.

Jul 12, 2010 | 1966 Ford Mustang

1 Answer

Wiring diagram 1966 Mustang


I would search the internet for it. That's the only advice I can give you for now. Also when searching put in Wiring Schematics instead of diagram.

Jul 11, 2010 | 1966 Ford Mustang

1 Answer

I need to know where to drill the hole. new fender has none. 1966 mustang antenna placement measurements


It is mounted on the passenger side, front fender about 2" inside of the finder edge and about 1" forward of the rear edge of the cowl vent. This photo gives you a good look. http://www.mustangdreams.com/Ford-Mustang-1966.htm To get an exact measurement find a 1964-73 Mustang and measure it.

Oct 10, 2009 | 1966 Ford Mustang

1 Answer

1966 mustang starts will not start.


Starts & can be driven, How far? Does it only go so far & quit? How's your choke settings on the carb?

Jun 02, 2009 | 1966 Ford Mustang

1 Answer

1966 Mustang is a C-4 or C-6?


Top is a C4, bottom is C6.
1faf944.jpg

May 25, 2009 | 1966 Ford Mustang

1 Answer

Ford mustang 1966 ignition problem.


The starter solinoid is bad.Clean and check battery cables also.

Jun 20, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...