Question about 1997 Chevrolet S-10 Pickup

1 Answer

Which way does the themosat gasket go on a 1997 chevy s10 2.2

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Thermostat If It's an O-ring it will go on either way and seal the thermostatic gasket. Removal & Installation 2.2L Engine To Remove:

  1. Drain the cooling system to a level below thermostat
  2. Remove or disconnect the following:
    • Radiator inlet hose clamp and hose
    • Water outlet housing mounting bolts and housing which way does the themosat gasket go on a 1997 - gm_truck_s10_tstat.gif

    • Thermostat and O-ring seal
To Install:
  1. Clean and inspect all parts for wear or damage
  2. Clean mating surfaces
  3. Install or connect the following:
    • Thermostat and the O-ring seal
    • Water outlet housing and bolts
      1. Torque to: 89 lb. in. (10 Nm)
    • Upper radiator inlet hose and clamp
  4. Fill with coolant
  5. Inspect for leaks

Posted on Jul 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Nissan Altima hestites to start and keeps getting hot Charges themosat, and water pump


IT MIGHT BE THE HEAD GASKET BRING IT BACK TO MECHANIC AND HAVE HIM CHECK HEAD GASKET IF ITS NOT THE HEAD GASKET ON ENGINE THEN HAVE HIM CHECK THE HEAT SENSORS

Nov 05, 2015 | Nissan Cars & Trucks

1 Answer

97 chevy suburban missfire cylinder #3 at start up


If you replaced the plug, wire and cap then it's either gona be the intake gasket seeping or a bad valve. Gasket more than likely I'd say bc the vortec motors are really bad about leaking or blowing the lower intake gaskets

Feb 20, 2015 | 1997 Chevrolet Suburban

1 Answer

97 chevy tahoe runs rough with a shake


A high idle is common with a vacuum leak. Ive done plenty of chevy intake manifold gaskets due to the gasket failing.

Jan 21, 2014 | 1997 Chevrolet Tahoe

2 Answers

I replaced the water pump ,rediator,themosat,on my 2002 oldsmobile aurora and it is still saying low engine coolant and is still overheating


first there is a low coolant sensor in the over flow bottle,and the other is that you have a common GM motor problem. all GM cars and trucks have a intake manifold gasket leak1_29_2013_6_16_48_pm.jpg1_29_2013_6_17_48_pm.jpg

Jan 29, 2013 | 2002 Oldsmobile Aurora

1 Answer

How to change oil on 1997 chevy venture


there is a drain plug on the bottom of the oil pan you remove to drain the oil its ether a 15mm or 14mm wrench while the oil pan is draining out unscrew the filter apply a thin coating of oil on the gasket of the new filter make sure the gasket from the old filter didn't stick to the engine install the drain plug and new filter add 4 quarts of new oil and run the car recheck for leaks and oil level that one holds 4 quarts or 4 and half not sure but 4 will be safe to start the engine

Mar 31, 2012 | 1997 Chevrolet Venture

1 Answer

How do i take the valve cover gasket off? 1997 chevy cavalier


just unbolt it and clean all of the old gasket off and put gasket sealant on the valve cover it self and put the gasket to it make sure it sticks to it good let it set to seal for a few and put it back on and torque it down to spec. or just try not to get it to loose or to where you crush the gasket ok and you prob. will be ok just remember gasket sealant is very sticky so yeah.

Mar 19, 2010 | 1997 Chevrolet Cavalier

1 Answer

I have a 1997 Chevy S-10 and the intake is leaking antifreeze out the back of the intake how do I change the manifold gaskets?the engine is a 4.3 liter V-6


actual changing the gasket is not a hard job. I strongly suggest you go to a parts store and buy a haynes or chiltons manual for your specific truck. these manuals will have step by step instructions for many different repairs for your vehicle

Feb 11, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Need help


make sure the push rod is seated into the lifter thats probable the problem

Jun 27, 2008 | 1997 Chevrolet Malibu

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...