Question about 1995 Dodge Ram 2500

1 Answer

What is the torque when replacing the rotor and hub on a 1995 dodge 2500 4x4 and what is the process

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

Front hub nut is 265 lbs at final , I usually take it to around 100 lbs on the first go and assemble the brakes ... then when the wheel is back on the ground I will finish the torque off at 265 lbs. If you don't have a torque wrench that goes that high put a 44 mm socket on a breaker bar with a 3 foot extension and stand on it... that will get you close.

Posted on Jul 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front right wheel bearing


This is a hub and bearing assy. You will need to remove the axle nut, brake rotor, caliper assy. There are 3 or 4 bolts that attach the hub assy to the knuckle assy. Most of the time, the hub assy will come out easy and sometime it comes out very hard. Make sure you torque the axle nut to the proper spec, so the bering will not fall apart and will last. Buy a quality hub and bearing assy, so you dont have to do it again.

Nov 03, 2013 | 1995 Oldsmobile Aurora

1 Answer

Removing hub assembly on 2001 dodge grand caravan 3.3L 2wd


Remove the axle nut. Place a punch in the fins of the rotor to lock the hub in place when the punch hits the caliper. Remove the caliper and rotor. Unplug the abs sensor Remove the three bolts holding the hub assembly to the knuckle. Remove the hub assembly from the knuckle. It is vitally important to torque the axle nut to the proper spec. Failure to do this will cause the barring to fail quickly! Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 17, 2012 | Dodge Grand Caravan Cars & Trucks

1 Answer

How do i remove the hub assembly from the front wheel of my 2001 dodge ram RWD?


  • Jack up your Dodge Ram. Block the wheels to keep it from rolling as you work. Get started by removing the first tire and wheel assembly. Remove the hub extension and the brake caliper as well as the caliper adapter.
  • Remove the grease cap, cotter pin, nut lock, nut, washer and outer wheel bearing. Now, pull the old rotor off of the spindle. Clean the area with a damp cloth to remove any debris. Pack the wheel bearings with grease.
  • Install the new rotor and hub onto the spindle. Replace the outer wheel bearing, washer, and then the retaining nut. Torque the nut to 30 to 40 ft. lbs. while rotating the hub and rotor. Then tighten the nut and install the nut lock and a new cotter pin.
  • Clean the grease cap and then coat it with new wheel bearing grease and replace the cap. Put the caliper adapter back into place and then tighten the two mounting bolts with a torque wrench. Install the wheel and tire assembly.
  • Repeat this process for each additional rotor and then lower the vehicle. Tighten the lug nuts and test drive your Dodge Ram to make sure that the installation was successful.


  • If I've helped, please vote!

    Dec 10, 2010 | 2001 Dodge Ram 1500 Truck 2WD

    1 Answer

    How do I replace right front wheel bearings on 1999 Dodge Dekota?


    Hi,

    It is a whole hub assembly. You remove the pin and unbolt the hub assembly and replace.

    What is needed is to raise your truck and support it with jack stands ( no concrete blocks) then remove the brake caliper and pads, be sure to support the caliper with mechanic's wire or what you have on hand that will do the job.

    Then remove the brake rotor "hat" then remove the cotter key then the hub retainer nut and remove the hub. The new hubs are greased so just replace the hub torque, install new cotter key the rotor hat and pads and caliper.

    I hope this helps.

    Nov 30, 2010 | 1999 Dodge Dakota

    1 Answer

    Procedure for front wheel bearing (hub assembly) replacement


    jack up vehicle wheel in question and install jack stand.remove wheel. Unbolt 2 caliper bracket bolts and pry caliper assembly up off brake rotor and hang off to the side with bungee.remove rotor . remove large axle nut. From the back of the hub remove hub bolts most commonly 15mm.Using a slide hammer style wheel puller the hub can be removed. if all you have is a big hammer hit the hub back and forth side to side until it can be removed. Bolt in new hub assembly and torque bolts.Install axle nut and torque. install rotor and caliper. reinstall wheel and torque.

    Nov 28, 2010 | 2001 Chrysler Concorde

    1 Answer

    How do I remove the rotor on my 1995 dodge 2500 4x4? My problem in the center cap holding it.


    Brake Disc (Rotor) REMOVAL & INSTALLATION
    1. Raise and safely support the front of the truck with jackstands. Remove the front wheel.
    2. Remove the caliper assembly and support it to the frame with a piece of wire without disconnecting the brake fluid hose.
    3. Remove the hub and rotor assembly.
    4. Install the rotor in the reverse order of removal, and adjust the wheel bearing as outlined in Section 1.
    INSPECTION If the rotor is deeply scarred or has shallow cracks, it may be refinished on a disc brake rotor lathe. Also, if the lateral run-out exceeds 0.010 in. (0.25mm) within a 6 in. (152mm) radius when measured with a dial indicator, with the stylus 1 in. (25mm) in from the edge of the rotor, the rotor should be refinished or replaced. A maximum of 0.020 in. (0.5mm) of material may be removed equally from each friction surface of the rotor. If the damage cannot be corrected when the rotor has been machined to the minimum thickness shown on the rotor, it should be replaced. The finished braking surfaces of the rotor must be parallel within 0.007 in. (0.178mm) and lateral run-out must not be more than 0.003 in. (0.076mm) on the inboard surface in a 5 in. (127mm) radius. Fig. 1: Use a dial indicator and micrometer to check the rotor for run-out and thickness 88479g83.gif
    Fig. 2: A correct final rotor finish 88479g84.gif
    Fig. 3: Location of the rotor minimum thickness marking 88479g91.gif
    Fig. 4: Exploded view of a rotor mounting to the hub — 4WD Dakota models shown 88479g90.gif
    prev.gif next.gifprev.gif next.gif

    Sep 03, 2010 | 1995 Dodge Ram 2500

    2 Answers

    Im trying to replace the rotors and im having a Hard time getting it off. HELP


    You might want to spray some WD-40 around the center of the rotor and the wheel lugs. Usually on Honda's, the rotors will have 2 threaded holes to put in bolts. Screw in each bolt equally to help push the rotor away from the hub.

    May 12, 2010 | 1995 Honda Accord

    2 Answers

    Am am replacing the wheel bearing hub assembly on a 2001 dodge dakota 4x2. How many pounds of torque do i aply to the spindle nut when replacing?


    understandably you want to do things right. i do this job by tightening the nut with channel lock pliers, spinning the rotor, and loosening the nut just til loose and then snug. reinstall the castle washer and then a new cotter pin (if available). make sure there is no lateral play(up and down). you should be good to go. happy holidays

    Dec 30, 2009 | 2001 Dodge Dakota

    1 Answer

    Need to remove and replace rear rotor


    You have to remove the axle shafts first as it has a full-floating axle, then pull rotor and hub off the axle housing. Unbolt rotors from hub. Check bearings and seals in hubs and the axle snouts where the bearings run before installing. Put new flange gaskets on axle and torque flange bolts to 95 ft-lbs.

    Apr 11, 2009 | 2004 Dodge Ram 3500 Truck

    1 Answer

    Front brakes


    Hi there;
    To replace the front rotors on your truck you will need to remove the hub & bearings, yes, how-ever you should not have to replace the bearings. If you take it a-part & find there is metal filings inside, then you would want to. But if the grease is only dirty you should just clean off all the old grease & repack your bearings.

    Word of caution: If you are not familiar with repacking & adjusting wheel bearings you may want to consult a local gaurage for a demonstration as if you do not do it properly you can cause a lot of damage to you & your truck.

    Having said that, once you get the hub off you will see that the rotor is bolted to the hub. remove the bolts, install the new rotors & install & torque the bolts.
    Hope this helps
    Farrout!

    Mar 17, 2009 | 1995 Toyota 4Runner

    Not finding what you are looking for?
    Cars & Trucks Logo

    123 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...