Question about 1983 Toyota Land Cruiser

1 Answer

I'm after an exploded parts view of the clutch master cylinder for a Toyota Landcruiser BJ41

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Go to your repair manual that came with the truck and if you don't have it you can download one on line at Toyota.com (it may cost a little but the manual will be worth it's weight in gold in the future!)
Good luck!
Rickster

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the clutch fluid located on Toyota hiace 1998 ?


Under the hood, on the firewall, there is the clutch master cylinder with a reservoir on it. This is where the fluid goes. Uses brake fluid, just like the brake master cylinder, also on the firewall. The clutch master only has one line coming from it-the line that goes to the clutch slave cylinder.

Aug 02, 2017 | Toyota Cars & Trucks

1 Answer

I have a 2000 toyota celica gt-s and it will not go into any gear?


Hi Sara,go check your clutch master cylinder,if low or out.it could be your clutch slave cylinder,here;s how to replace.Here's the part.Here's how to bleed.

Nov 03, 2013 | 2000 Toyota Celica

1 Answer

How to change a clutch master cylinder on a 2006 toyota tacoma


remove line from the side of clutch master cylinder two bolts or nuts on firewall inside vehicle is a pin on the upper side of clutch remove and pull old unit out bench bleed new master by filling and pressing in on the piston of the master cylinder. if you dont have a hose fitting dont bench bleed bleed it in vehicle( this method takes longer) install back in vehicle and hook it all back up torque bolts to 25 ft lbs then bleed the slve cylinder from under vehicle near back of motor just like bleeding brakes pump up hold and release the line pressure by opening valve on slave cylinder.

Apr 06, 2013 | 2006 Toyota Tacoma

1 Answer

1979 landcruiser clutch did not release fully to get it into gear.I had rebuild the master and slave silinders.The problem is stil the same.


Problem might be on the Clutch plate is won or Preasure plate is weak wants to be changed. or sometimes your slave cylinder is won inside, fix complete new one and then see before going deep in the gearbox.

Aug 27, 2011 | Toyota Land Cruiser Cars & Trucks

2 Answers

My clutch doesn't always disengage when the peddle is on the floor and when starting out in first bolts ahead as though the clutch was already part way out. I took it to a shop and they said my clutch...


your clutch master cylinder is right beside your brake master cylinder. I would advise you to replace the master cylinder and the slave cylinder together. The slave cylinder is on the side of the transmission. The slave cylinder does have a bleeder screw on it after the parts are bolted in place fill with dot 3 brake fluid and open the bleeder on the slave cylinder until fluid starts dripping out. Then tighten bleeder then open bleeder and have someone push down on clutch pedal while the pedal is pushed down tighten the bleeder the release pedal. Repeat this procedure until you get no air and the pedal feels normal and you should be good to go. Good luck!

Apr 14, 2011 | 1991 Toyota Celica

2 Answers

Clutch pedal is no longer operating normaly and appears to be frozen. Is there a hydraulic reservoir component to this system?


Yes, the reservoir is part of the Clutch Master Cylinder Assembly. Below is an exploded view of your Clutch Master Cylinder. The master cylinder mounts to the firewall in the engine compartment directly in front of your clutch pedal. Note in the picture the part marked "pushrod". This is what actually connects to the clutch pedal itself.


dttech_5.gif

Jan 26, 2011 | 2000 Hyundai Elantra

1 Answer

CLUTCH ADJUSTMENT 1997 TOYOTA COEOLLA


This vehicle has a hydraulic clutch system check the fluid level in the clutch master cylinder it is located on the firewall near the brake master cylinder fill it if its low than check hydraulic system for leaks, possibly slave cylinder, you will have to rebleed the system if part replacement is neccassary

Apr 11, 2009 | 1997 Toyota Corolla

1 Answer

Clutch problem,


common problem,I would replace the clutch master and slave cylinder try to use toyota parts as they work best,although there are great aftermarket parts houses,if you need any more info let me know.have a good day DB

Feb 15, 2009 | 1996 Toyota T100

1 Answer

MR2 after 2 mins of starting the smt light comes on.


it sounds like the clutch actuator is worn out.
The clutch actuator has 2 parts:
1. the clutch master cylinder
2. the clutch slave cylinder.

Try to replace the slave cylinder first, and if it is still not solving the problem, then try to replace the clutch master cylinder

Good Luck

Feb 06, 2009 | 2003 Toyota MR2 Spyder

Not finding what you are looking for?
Cars & Trucks Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...