Question about 1983 Dodge Pickup

1 Answer

I have a 1983 dodge d150 witch had a 360 untill engine swap to a 318. the 318 ran great for a couple miutes and then it all quite. i have no ignition or electrical of any.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Star by checking all the ground straps from batt to block and engine to body, me guess is you missed one

Posted on Jul 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 dodge with a 2001 360 dodge magnum motor 600cfm edelbrock carb, air gap edelbrock intake. new plugs (e3s) new wires new coil new ballast.. is all in time.. wont start help


Are you getting spark? You've put a 2001 engine into a 1986 body. The 2001 engine ran with an engine control module (ECM), the 1986 doesn't have that. The 1986 probably has an electronic ignition module that works with the 1986 coil and 1986 reluctor/distributor. You may want to compare the two distributors and the two coils.

Sep 12, 2016 | 1986 Dodge D150

1 Answer

I have a 1998 dodge Dakota 5.2 l that I'm thinking of swapping. ...what years are comparable and with what vehicles ......and how difficult would it be to upgrade to a 5.9l r /t model engine ?


the 360 and 318 are basically the same engine except the 318 is externally balanced and the 360 is internally balanced be sure when you do the swap get the flywheel and comes with the balancer i believe they are the same from 96-01 before they went to the 4.7 engine

Apr 14, 2015 | 1998 Dodge Dakota

1 Answer

1983 dodge d150 with 5 speed manual transmission ran perfectly then all of a sudden the radio dash and engine turn off but the headlights stay on ad=nd brake lights still work. now the truck makes no...


You have a blown fuseable link under the hood. Look in the driver side you see wires wrapped up unwrap and check each wire. Replace blown wire and should fire up.

Jun 19, 2014 | 1990 Dodge D150

1 Answer

I have a 1991 d150 318 that wont start.


Have you tried using WD-40 as a quick start, spray in to air intake at throttle body and see if it tries to fire up?

Feb 24, 2013 | 1989 Dodge D150

1 Answer

1986 dodge d150, 318 cu engine Truck starts sometimes, could idle for an hour or longer then just quits, not like a fuel problem quits no sputtering just dies like turning the ignition off. Coil is good...


Check your ballast resistor, they are a major failure item. The ballast resistor lowers the voltage to the coil and uses resistance to do so. Test would be to put battery voltage to positive side of the coil, during the failure condition, but my bet is resistor.

Aug 30, 2011 | 1991 Dodge Ram 150

2 Answers

Where is the ignition module located for a 1987 Dodge D-150 with a .318 motor?


It's in the engine compartment. On the drivers side firewall below the master cylinder next to the fender

Dec 26, 2010 | Dodge D150 Cars & Trucks

1 Answer

Have 89 d150 just put 318 with 430 lift cam magnum heads 1.6 rockers witch i think bumped cam to about 480 lift.disconected the computer **** and made it carberated. still using electric fuel pump and...


You might just try bumping up the fuel pressure to 12PSi.
you useing a double pumper you need at least that.
I might need more info but sounds like a cool ride.

Dec 02, 2010 | 1989 Dodge D150

1 Answer

I have 1992 Dodge D150 with 318 magnum. It won't


is this vehicle fitted with a chipped key ?? iam thinking factory immobilisor here?? but not sure what year it was introduced in america

Nov 22, 2009 | 1993 Dodge D150

1 Answer

Engine swap


I just put a 96 360 magnum in my 97 dodge 4x4 that had a 318 in it. Yes it does fit. I noticed that the flex plate on the 360 has balance weights on it and the 318 does not. Make sure the plate stays with the 360. The torque converter and exhaust manifolds bolted right up. The 96 360 engine had different connector plugs on the Map sensor, Crank Sensor and Tps. Get those off of your 318.
I did notice that with the 96 PCM for the 360 my fuel guage was off quite a bit. The 360 will run off of the 318 computer at least if your in a bind for Money.

Oct 04, 2008 | 1997 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...