Question about 1998 Plymouth Neon

1 Answer

Motor mount for a 98 neon

What would make my 98 neon engine tilt too one side? I heard a loud pop when i pulled into the driveway. I opened the hood and the engine is titled to the left side (pulley side)

Posted by on

  • mak95500 Jul 29, 2010

    I looked at the coils on both side they are OK. actually engine is tilted so much that the pulley is touching the wheel-well Passengerside. how many motor mounts are there? the one in the front looks OK but i really cant see the entire mount

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

Broken front coil spring , look in the wheel well .

Posted on Jul 29, 2010

  • Ron
    Ron Jul 29, 2010

    There is only one on that side .. you may have to jack the motor up to see how nad it is.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I recently had 2 motor mounts on my 2005 dodge neon replaced. After I got my car back, I noticed it was making a weird noise, can't quite describe it, just knew that I hadn't heard it before. Then...


I also had my engine mounts replaced on my 2005 Dodge Neon. I have the same sound going on right now. When I spoke to a Auto Parts guy, he looked at it and said it was my tension-er pulley, and that when it runs out of grease it is a screeching noise and will be metal on metal. If you are looking at the front side of your car at the hood. It is the belt and pulley's that are on the left of the engine. (other side of battery). The tension-er pulley is the almost triangle looking piece located behind the back side of the belt.

They belt not being tight enough could also be why when I start my car, it seems to be rough starting.

I plan on getting this fixed ASAP. Perhaps your's went out and is now why the difficult steering.

I know this is not a solution, but it might help.

~ Tammy

Dec 30, 2010 | 2005 Dodge Neon

1 Answer

Stuck hood on 2002 jag S type


Try and bump the top of the engine or just have some one hold the release latch and lift up on the engine until it pops open.

Mar 02, 2010 | 2002 Jaguar S-Type

2 Answers

Engine Roll Damper???


i've heard it called a few different things, but not sure i've heard roll damper. i think they may be talking about a torque strut (what i've heard it called) it's like a dogbone looking engine mount, usually mounted near the top of the engine. its purpose is to keep engine from bucking back and forth while the engine is torquing. its basically a motor mount, but without any real pressure on it at rest. easy to replace, that is, if that 's what they are referring to

Feb 19, 2010 | 1997 Dodge Neon

2 Answers

1998 Plymouth Neon--Hood Latch Repair


Have you tried lubricating, or spraying mechanism where hood latches in with WD-40 or similar, to see if latch is obviously releasing & may be slightly seized. is the handle & cable that you pull to open the hood appear slack or sloppy ?

Feb 15, 2009 | 1999 Plymouth Neon

3 Answers

Loud Electric Screwdriver Sound coming from the Engine


it sounds like it was just the electric fan turning on, they can and will turn on even if car is turned off.

Oct 26, 2008 | 2004 Dodge Neon

2 Answers

I have a Plymouth, Neon 1997. The timing belt tensor was making loud noises. The mechanic replaced the tensor and the timing belt. But, now the car shakes when iddling. Once it gets moving the shaking will...


A motor mount not installed correctly?Open the hood and put the emergency brake on,with someone looking at the motor put the car in drive,press on the brake and give a little gas---if the motor moves up the mount may be the issue.

Jul 30, 2008 | 1999 Dodge Neon

1 Answer

98 dodge neon


if 2.4l or 2.0 is about the same you will have to pull your balancer pulley then take off the guard around it then loosen the timein tincher then take your timein belt off then you should see your water pump everything is going to be on the side of the motor and probably will have to put a jack up under the motor and take the motor mount off the side of the motor.

Jun 19, 2008 | 1998 Dodge Neon

Not finding what you are looking for?
1998 Plymouth Neon Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...