Question about 1987 Dodge Pickup 2WD

1 Answer

MOTOR MOUNT REPLACEMENT HALTED

Greetings: After replacing the passenger side motor mount on a 1987 Dodge 100 2wd, I went to replace the driver's side and found that a wrench cannot be mounted on the underside of the motor mount - recessed the way it is. Went to pull the bracket the bottom part of the old mount is attached to and cannot get it loose after pulling the bolts we could find. Seems there is something holding it at the top? PLEASE HELP...THIS A A DONATION OF TIME TO A POOR FAMILY ON MY PART AND I NEED TO GET BACK TO OTHER WORK. May God Bless, Thor Lakemont GA

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

You have to undo both mounts and lift the motor a couple inches to get at it.

Posted on Jul 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace driver's side window on a 1987 dodge dakota


you need to remove the inner door panel and unbolt the glass from the regulator

Aug 22, 2012 | 1987 Dodge Dakota

1 Answer

Where is the master cylinder in the 1987 Dodge Aries?


The Master Cylinder On most all american vehicles is located on the drivers side on the firewall. It usually has a brake fluid reservoir mounted to it.

Jul 30, 2012 | 1987 Dodge Aries

2 Answers

Where is the fuel filter in a 1987 delta 88


in carborator where fuel line enters carb remove 5/8 in line then remove 15/16 nut where 5/8 line went in fuel filter is behind 15/16.nut replace seal (plastic) replace fuel filter GOOD LUCK B. HARRIS A.S.E. CIRTIFIED 25YRS. EXP

Apr 28, 2011 | 1987 Oldsmobile Delta 88

1 Answer

Drivers side mirror doesn't work when I try to adjust with switch passenger side does


Try moving the mirror by hand at first incase the motor is stuck and then try with the switch. If that doesn't work, then either you have a loose connector or the motor went bad and needs to be replaced.
Benjamin

Aug 22, 2010 | 2006 Dodge Grand Caravan

1 Answer

I replaced the driver's side window motor because


I don't know everything there is to know about window motors, but I have seen this before, both mine went out at the same time, not together but a couple weeks apart, like they were dated. Anyway, I replaced both motors, then both operators. Now they both work fine. I would hang on to the old motor, you never know, it might be good, You might have a bad switch on the door, I had to take my switches apart on my other truck and clean the contacts, got both motors working again, Hope this helps.

Mar 20, 2010 | 2003 Hyundai Tiburon

1 Answer

How can i replace engine mounts on 94 dodge


grab a block and a jack then place jack under engine or transmission, then put pressure on it, then remove center support bracket on bottom remove mounts install new ones reinstall center bracket line up mounts in bracket tighten center bolts remove jack and block

Mar 15, 2010 | 1994 Dodge Intrepid

1 Answer

2003 dodge neon motor mounts are causing vibration at accelerated speed


there is a motor mount that attaches frum the passenger side wheel to the tming cover. this is the mount that usually goes bad. you have to remove the wheel to see the torx bolt at the wheel well. than there are bolts on the other side of the wheel well. after you get those the ones at the motor have to be removed. you will have to place a jack under the oil pan use a piece of wood with the jack. you also have to take the top mount of first. thats pretty easy to replace.

Feb 11, 2010 | 2003 Dodge Neon

2 Answers

I need to replace the motor mount thats on the passenger side,abd you access the main bolt thru the wheel well,it's a 2005 2.0,do you know what they call that motor mount


hello. you have 5 mounts front left side, front right side, lower strut rear of engine,upper strut right side and transaxle rear left side

Sep 14, 2009 | 2005 Dodge Neon

2 Answers

Passenger Window Stuck all the way Down


Try switching the power window switch from the passenger side to the drivers side. Before you do that try with the switch on the up position, wiggle it from side to side. The contacts may be worn and by wiggling it may make contact. Other then that try to park it in side or garbage bag taped to keep rain out till you get it to the shop.
Hint, take it to a Auto window repair shop to replace the switch if it's bad or if the motor is bad. They have more experience to removing the door panels and removing the power window regulator (motor) if that needs to be replaced.
Good luck and hope this helps. 

May 30, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...