Question about 1998 Ford Aerostar

Open Question

C1145 fault code for wheel sensor on a focus cmax changed the sensor but abs light still on

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76164 Answers

SOURCE: abs fault

check and make sure u did not damage or disconnect the wheel sensor(s), that would be just about the only thing u could have done to cause this issue, u might want to have the system tested for trouble codes to confirm this wheel sensor possiable fault.

Posted on Mar 10, 2009

Ad
  • 1 Answer

SOURCE: How do you reset ABS light\system after replacing

turn the ignition to on position and disconnect one of terminals of battery for 30 sec to one minute and reconnect battery . turn off ignition and restart vehicle . If that doesn't work go to dealer .

Posted on Oct 29, 2009

  • 599 Answers

SOURCE: DSC fault light is on, also brake fault light, ABS

Have the car scanned for codes, you must use a scanner capable of reading European cars,anything else is just guessing. get me the codes and we'll go from there, get back to me and we'll solve this problem Thanks Ray

Posted on Feb 17, 2010

  • 279 Answers

SOURCE: abs kicking in at low

C1145 RH Front Speed sensor cct poss faulty sensor.
C1155 LH Front Speed sensor cct poss faulty sensor.
C1178 Unknown

Sorry can't be any more help than this

Posted on Dec 19, 2010

tunde007
  • 2382 Answers

SOURCE: Mazda 626 (Capella) ABS fault. I

Hi,
Code 44
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 48
Misfire Diagnosis. Check the ignition and fuel systems.

Posted on Jan 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced wheel bearing and speed sensor on RF, 2000 f350 diesel dually. Drove 1 month about 1000 miles, now I get c1145 and c1230 with abs light. Any ideas?


ABS code C1145 - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 1997 - 2003 F150
Aug 20, 2009 - ABS code C1145 1997 - 2003 F150. ... C1220 Yellow ABS WarningIndicator Failure (2) C1222 Wheel Speed ... C1230 Rear ABS Sensor (Electrical/Static) (2) ... ABS light on (Anti Lock Brakes) and I hear pump when in turn ...
Oct 9, 2010
ABS code C1206-2003 F150 SuperCrew
Aug 13, 2007
ABS light C1230
Oct 22, 2006
ABS light on DTC's C1229,C1230
Nov 18, 2002
More results from www.ford-trucks.com

Nov 17, 2015 | Cars & Trucks

1 Answer

After replacing my rear abs speed sensor, my abs light is still on.. i'm on rear discs


Any code that store into the computer need to be manually erase
by a scaner after the problem is fixed.


Mai

Mar 21, 2013 | 2003 Ford Focus

1 Answer

2006 ford crown vic abs code b1596


B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .

Jan 14, 2013 | 2006 Ford Crown Victoria

1 Answer

I have trouble codes P1603 and C1145. What do they mean?


P1603: Transmission Control Module (TCM) EEPROM Failure
C1145: Front right wheel speed sensor input circuit failure

The P1603 means that your TCM has probably failed. It may have a loose solder connection or the PROM chip may have come out of it's slot. EIther way the TM needs tobe removed from the car and repaired/replaced by a qualified repair person.

The C1145 is for the ABS and it may be related to the TCM failure. I am not that familiar with the Jaguar ABS system, but that code means the signal from the front right wheel is bad. May be the sensor or the "tone ring"...

Jun 15, 2011 | 2002 Jaguar X-Type

1 Answer

My engine and abs lights are on. I replaced the rear ABS sensor, then replaced both front speed sensors!!! Now have codes C-1145 and C-1175 and P-1000!!


C1145 is a Right Front wheel speed sensor fault
C1175 is a Left rear wheel speed sensor fault.
P1000 System OBD check not complete since last memorie clear which mostlikely means that the car has not completed the drive cycle to set all monitors for the engine emissions. ( it may just need to be driven a more.
As for the wheel speed sensors if you have replaced them the ABS codes need to be cleared. the engine code reader and clearing tool will not do it. A scanner with ABS capabilities is needed. On some cars if you disconnect the battery and wait 3 mins then re connect the battery, that will clear all codes. then the car needs to be driven to set all monitors for engine emissions.
If you have already cleared the codes. and you have repete same codes for the ABS, you would need to look the wireing over for possible wire rubs that are causing the faults. or the ABS computer itself is at fault.

Apr 01, 2011 | 2002 Jaguar X-Type

1 Answer

Abs kicking in at low speeds no light on 3codes stored and cleared c1145,c1155 , c1178 . have checked rear relucter discs on c.v joints o/s and n/s intact / removed sensors for better look, ok corroded...


C1145 RH Front Speed sensor cct poss faulty sensor.
C1155 LH Front Speed sensor cct poss faulty sensor.
C1178 Unknown

Sorry can't be any more help than this

Dec 16, 2010 | 2003 Jaguar X-Type

2 Answers

My abs light stays on on my ford focus


when the ABS light stays on it means there is a fault present in the ABS system and the ABS has been disabled, as long as the light is on u just have regular brakes with no ABS, there are many thinbgs that can turn the light on, most common is one of the wheel speed sensors is defective, since these sensors are about $75-100 each and there are 4 of them guessing is a poor idea, so what u need to do is have the ABS systwem tested, there will be a fault code present to help narrow down the defective part or wiring.

Dec 28, 2009 | 2004 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...