Question about 1989 Ford Bronco II

1 Answer

My brakes wont bleed in my 1990 ford bronco 2

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

Have you tried bleeding at the master first ?

Posted on Jul 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant find the inertia switch on my 1990 ford bronco eddie bower edition


The inertia switch should be located under the drivers side dash assembly near the steering column. It is very close to your brake light switch on the brake pedal. Hope this helps.

Aug 17, 2011 | 1990 Ford Bronco

2 Answers

Brakes wont work pedal goes to floor changed the master cyclinder bleed brakes and still have same problem 1990 ford aerostar van


What is the condition of both front calipers? both rear wheel cylinders? and the complete brake lines and hoses of your van? If they are all good with no traces of leakage, then did you bleed the Mastercylinder on the bench first before installing in the van? Did you gravity bleed the 4 wheels first? did you bleed from the farthest wheel first? Are you using a new Master and not a re-built??

Feb 25, 2011 | 1990 Ford Aerostar

1 Answer

No brakes at all on my ford bronco 1990


sound's like the master cylinder has packed it in , make shure u don't have a leaking brake line, the master cylinder is on the drivers side of the fire wall, check the fluid level then go from there

Jun 05, 2010 | 1990 Ford Bronco

1 Answer

1990 ford bronco 2 2.9 liter its leaking oil between the block and the oil filter bracket


The gasket must have let go you'll to remove the oil filter bracket and replace the gasket. Make sure you get all the old gasket off and clean both surfaces with brake parts cleaner or carburator cleaner, you want the parts clean and dry. If you use gasket sealer to put the new one on, use it sparingly, just a film is pleanty.

Jan 03, 2010 | 1990 Ford Bronco II

1 Answer

Need directions to bleed slave cylinder on '89 bronco 2 4x4


brakes or clutch??,if clutch get assistant to work pedal ,pump a few times then hold down ,you push the clutch arm in with a bar and open the bleed nipple at the same time then close the nipple and repeat ,after about 3/4 goes it should have pressure

Dec 22, 2009 | 1989 Ford Bronco II

1 Answer

Lost brakes, told to replace brake cylinders,trying to bleed but pedal does not get firm. front part of master cylinder resivoir churns? this is on a 1990 ford bronco.


If you have replaced the master then you should get all the air out before it becomes alright.Now is there any leak somewhere?Did you use all the rubber seals?Check if there is no leak on the system..like a corroded pipe etc...

Nov 03, 2009 | 1990 Ford Bronco

2 Answers

1988 ford bronco 2 break problems


front or back is it leaking brake fluid

Mar 09, 2009 | 1988 Ford Bronco II

1 Answer

Brake replacement


take the brake caliper off, this is the part that holds and moves the brake pads thare will be 2 bolts holding it on ,one on top one on bottom. after taking bolts loose you may half to pry the caliper up and off brake rotor. once this is done remove old pads and use a brake caliper piston retraction tool to push the piston back into the caliper. you can get this tool at your local parts store or use a C clamp with one of the old brake pads to push it back.install new brake pads and install caliper .after completion make sure you pump the brakes till you get a good pedal before moving vehicle

Dec 26, 2008 | 1990 Ford Bronco

1 Answer

Rear brakes not working on 1990 ford bronco 4x4


check your break lines or remove the tires and pull off the brums and look at the automatic adjusters

Nov 24, 2008 | 1990 Ford Bronco

1 Answer

Changing brakes and rotors


Remove te cross pins that hold the caliper and the brake pads in place, then remove the caliper bracket, there are 2 bolts at the backside, then the rotro just slides off, clean any rust on the rotor mount area while the rotor is off, then using a large clamp depress the piston in the brake caliper and reinstall in reverse order, one word of caution, use quality replacement parts, Wagner is very good, if you don't use good parts you will end up with poor brake performance.

Oct 15, 2008 | 1990 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...