Question about 2000 Dodge Durango

1 Answer

Won't start I changed fuel pump checked the sparke plugs,an checked the injectors with a noid light.. All works !! Now the deal is it turns over it started for about 3 sec an shut off...it's got me lost

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

They have a relay marked asd in the under hood fuse box... try swapping it with another.

Posted on Jul 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2004 dodge durango, 4.7l turns over but won't start. It did it 2weeks ago was told electrical problem n fixed. Did it again 3 days ago and it started without anyone doing anything to it the following...


Durangos are known for crank sensors to go bad. Make sure that your battery is fully charged so you know that isn't an issue. If you don't have the proper equipment, try this.. Your going to need someone else's help for this. Pull one of the spark plug wires, using a screwdriver, put the tip of the screwdriver into the wire and hold the shaft of the screwdriver about a quarter inch away from a good ground source. Have your assistant turn the key and crank the engine while you check to see if you have spark. If you can, visit your local parts store and ask for a noid light that will fit your vehicle. It's usually about $10-$12. The purpose of the noid light is to check for injector pulse. Disconnect the plug for the injector and connect the noid light in it's place. Once again, crank the engine and check to see if the noid light lights up and pulses. If the crank sensor is bad, you should have no spark and no injector pulse. Replace crank sensor if so. If you have spark, check for fuel and or fuel pressure. Listen for the fuel pump to energize when the key is turned. Also try spraying starting fluid into the throttle body. If it starts, your having fuel issues. I hope these tips help. Good luck.

Feb 21, 2015 | 2004 Dodge Durango

1 Answer

Car won't start


Hi there:
You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Oct 04, 2012 | 1998 Acura CL

1 Answer

Dead cylinder number 2 bad injector number 2


use a digital volt meter,put it on the ohm scale check number 2 fuel injector should be 11 to 16 ohms if not reads zero fuel injector faulty.if numbe 2 fuel injector okay.use noid light hook it to fuel injector electrical connector with fuel injector disconnected and see if pcm is firing the fuel injector noid light should blink when cranking the engine.if light steady pcm not firing 2 fuel injector,if noid light dont light up.there is a open in the wiring connector 2 fuel injector 2. if fuel injector okay,check spark plug, carbon foul you have a bad ignition coil or wire if you see oil on spark plug you have worn piston ring or leaking valve guides allowing oil to foul out spark plug.do a compression test check compression to see condition of the cylinder.

Sep 01, 2012 | 2005 Pontiac G6

1 Answer

Car won't start


You will have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Apr 14, 2012 | 1999 Cadillac Escalade

1 Answer

I have a 89 f250 with a fuel enjected 460 it started one day then went out to start it the next an it wouldn. All it does is fire but wont start. Ive check everything I can think of. Its like its flooding...


Must be a fuel problem, since you are getting spark. Can you hear the pump turn on when you turn the key to on? I would check the injector circuit, and if it is working, have the fuel pressure checked-might be too low from a weak or tired pump.
The injectors have a hot wire to them-always hot with key in on position. There's also a fuse for the injectors, as well as a fuse for the fuel pump. The ground wire from injectors goes into the engine computer so it can control injector pulse. A tester called a "noid light" can be used to check the injector circuit. Just plug it into the injector connector and crank the engine over. If the noid light is blinking, the circuit is working right.

Oct 25, 2017 | 1989 Ford F 250

1 Answer

I have 94 e250 5.8L van 4x4 and it won't turn over


Hi Nick:
You wll have to pinpoint what the engine is missing...
- Spark
- Fuel
- Compression

All three of these are tested when the engine is being cranked over. There are two way of checking for fuel. Fuel pressure and fuel trigger. Both are very important and must be present for the engine to start. Fuel pressure is self explanatory. You just hook up the gage and see what the reading is. Fuel trigger is check with a noid light. The injector gets unplugged and the noid light gets plugged in to the injector clip. With the engine cranking over, this light must blink. This is the signal to the injectors from the computer. You can have all the fuel pressure in the world, but it wont matter if the injector is not pulsing gas into the cylinder like it should.

Compression tester, spark tester, fuel pressure gage and noid light are all accessible at your local auto store. All three tests play a very important part in diagnosing a no start condition. Be extremely careful when doing these tests.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 09, 2012 | 2002 Ford E250

1 Answer

98 crv won't start


Check compression and timing belt. If belt is ok and you have compression, check to see if you have a pulse at the injectors. You use a device called a NOID light (basically a light bulb that plugs into the injector plug. Unplug the injectors one by one and plug the light in then crank the engine. Light should blink on and off if the system is working properly. If not check for a bad crank sensor, blown injector fuse and wiring harness. Hope this helps.

Nov 02, 2011 | 1998 Honda CR-V

1 Answer

Replaced the Fuel Delevery System/Pump and the in-line fuel filter on my 93 GMC Vandura Van 2500. Van turnes over; however, no fuel in getting to the engine. I have checked the Fuel Pump...


install a fuel pump guage and check pressure at key on and start, it should hardly vary, it the pressure is constant check the injector signal with a noid light, while you are at it check spark(no spark no injector signal) you won't find a relay fuse

May 07, 2011 | GMC Vandura Cars & Trucks

2 Answers

Wont start, cranks strong.


fuel pump, computer, anti theft system,crank sensor

Oct 14, 2009 | 1998 Ford Mustang

1 Answer

84 toyota supra 5 speed man.


sounds like ecm. car starts but when it switches over to run setting from cranking setting the cumputer ecu doent activate the run curcuits which may control your fuel injectors. check to see if engine has spark. remove one plug wire from spark plug put it close to the valve cover if you see an arc then you know that you have spark. then also go to fuel pump in tank and check voltage on the power wire if you have good voltage and the pump doesnt make any noise while ur cranking then it may be a fuel pump if the pump is making way to much noise then check the fuel pressure by hooking up a fuel pressure gauge. all test are to be done while someone cranks the engine. noid light for the injectors, disconnect on injector electical connetor connect the noid light to the wire that u just unplugged from the injector. the light will flash while u crank , once it goes to the run circut the light will either stay on which will shut off ur car or the light will stay off which will do the same. if the noid light did what I said when it went to the run circut then it is what controls your injectors...ecm good luck....daniel

Oct 11, 2008 | 1984 Toyota Celica Supra

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...