Question about 1996 Chevrolet S-10 Pickup

1 Answer

How do i remove a starter of 96 s-10 engine 2.2

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

First unplug batterie . jack the truck and go under and locate starter . .Un hook the 3 wires then undo the bolts , pull back a little and out it comes . reverse directions to install a new one . Very simple job.but very costly if a garade does it.

Posted on Aug 07, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 96 Chevy S-10 starter problems

Just did this, take the long bolt out of the passenger side engine mount, loosen the two transmission mount bolts and jack the right side of oil pan slowly, when you do this there will be enough clearance between the bell housing and frame, be sure to use a jack stand to be safe.
Put the starter motor in the space with the selonoid up and wiggle forward into position then insert bolts and hook up connections. Let the motor down, put the motor mount bolt back in, tighten transmission mount.

Posted on May 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on a 2008 pontiac g 6 4 cylinder


Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the "S" terminal connector from the starter solenoid. Remove the engine harness lead (2) from the starter
Remove the positive battery cable nut (2) from the starter solenoid. Remove the positive battery cable (3) and engine harness terminal (4) from the starter solenoid.
Remove the starter motor bolts. Remove the starter motor.
Has four engines possible in your G6 ,starter removal is simalier for all except one the catalytic converter has to come off.

Mar 30, 2015 | 2008 Pontiac G6

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

Ho w do i replace starter to a 1998 trooper and where is it located? pictures would help.


Read here before you replace the starter.
Bear in mind that the starter solenoid usually fails long before the starter motor itself and is a much cheaper repair.
Starter is on the LH rear of the engine.
NB!! : Whenever you work on the starter first remove the battery negative cable.
On V6 engines remove the LH exhaust downpipe(1).
Remove heatshield(3), 2 electrical connections and then the 2 bolts that hold the starter to the transmission.
On 4 cylinder engines it is possible to remove the starter by just removing the 2 electrical connections and then unbolting the 2 bolts holding the starter to the transmission. In this case an assistant is nescasary to help with holding the nut in the engine bay while you unbolt from the bottom of the vehicle.681bb13.jpg

Sep 23, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

3 Answers

How to Replace the Starter in a 1999 Pontiac Grand


starter is located on the engine block down below.

Removal & Installation To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.
  1. Remove or disconnect the following:
    • Negative battery cable
    • Radiator lower air deflector
    • Torque converter cover
    • Electrical connections from the starter
    • Starter motor
To Install:
  1. Install or connect the following:
    • Starter motor and torque the bolts to 32 ft. lbs. (43 Nm)
    • Starter solenoid BAT terminal
    • Starter solenoid S terminal
    • Torque converter cover and torque the bolts to 89 inch lbs. (10 Nm)
    • Radiator lower air deflector and torque the bolts to 15 ft. lbs. (20 Nm)
    • Negative battery cable
Starter removal/installation – 3.1L & 3.4L engines 9306zg15.gif

Starter removal/installation -3.8L engine 9306zg17.gif

Jul 15, 2010 | 1999 Pontiac Grand Prix

1 Answer

How do i remove the starter?


Removal
1. Disconnect negative battery cable. Raise and support vehicle. As required, remove nuts from A/C
compressor, exhaust system and/or engine braces, adjacent to starter. On M/T models, remove bending
brace from around starter (if equipped). On all models, remove other items that may interfere with
removal of starter.
2. If necessary, remove nut from engine cross brace. Using pry bar between upper engine mount and engine,
pry rearward and support engine.
3. If necessary, remove oil filter, air induction tube and cooling fan. Remove flywheel inspection cover (if
equipped). Remove starter solenoid terminal "S" nut and battery cable nut. Separate wiring from starter.
Remove starter mounting bolts. Remove shims and note arrangement for reassembly. Remove starter.
Installation
Before installing starter onto engine, tighten inner solenoid terminal nuts to ensure they are secure in cap.
Starter failure may occur due to terminal or cap damage. Install starter and wiring. Ensure shims are installed in
original location.

Jun 25, 2010 | 1996 Buick Regal Olympic Gold

1 Answer

Where is the starter in a 1995 nissan pathfinder


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
4178adf.jpg


Fig. 1: Starter removal on 4WD-6-cylinder engine

74f3669.jpg

Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.

Hope this help (remember rated this).

May 18, 2010 | 1995 Nissan Pathfinder

1 Answer

Where is the starter located on 2002 intrepid


Underneath the car. somewhere near where the engine and transmission hook up.

Removal & Installation
2.7L Engine

1. Remove or disconnect the following:

Negative battery cable from the remote ground post

Battery feed and posi-lock connectors

Nuts from the catalyst support bracket and mount

Starter heat shield

3 starter-to-engine/transaxle bolts

Starter by rotating it toward the engine and sliding it rearward between the catalyst and the engine mount


To install:

1. Install or connect the following:

Starter by sliding it forward between the catalyst and the engine mount and rotating it away from the engine

Starter and torque the 3 starter-to-engine/transaxle bolts to 40 ft. lbs. (54 Nm)

Starter heat shield

Nuts to the catalyst support bracket and mount

Positive battery cable and torque the nut to 89 inch lbs. (10 Nm)

Posi-lock connectors

Negative battery cable to the remote ground post





3.2L & 3.5L Engines

1. Remove or disconnect the following:

Negative battery cable from the remote ground post

Starter-to-engine/transaxle nut and bolts

Positive battery feed wire from the starter

Starter and position it to gain access to the posi-lock connector



2. Place a support under the engine and slightly relieve the pressure from the left engine mount.

3. Remove the 3 left engine mount-to-engine bolts.

4. Slightly, raise the engine to provide more room.

5. Remove the starter by sliding it rearward between the catalyst and the engine mount.

6. Remove the posi-lock connector.

Click image to see an enlarged view

Fig. Removal and installation of the starter motor



To install:

1. Install or connect the following:

Posi-lock connector

Starter by sliding it forward between the catalyst and the engine mount



2. Slightly, lower the engine.

3 left engine mount-to-engine bolts

Positive battery feed wire to the starter and torque the nut to 89 inch lbs. (10 Nm)

Starter and torque the starter-to-engine/transaxle bolts to 40 ft. lbs. (54 Nm)

Negative battery cable to the remote ground post


Hope this help (remember rated and comment this).

Mar 27, 2010 | 2002 Dodge Intrepid

1 Answer

How to replace the starter


Toyota Celica, Corolla, ECHO & MR2 1999-05
Starter - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Radiator upper support seal
Air cleaner
Engine under covers
Starter wiring
Starter

3. Installation is the reverse of removal. Torque the bolts to 28 ft. lbs. (37 Nm). Note that the bolts are 2 different lengths.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Battery and tray. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
Coolant reservoir
Reservoir hose from the radiator
Right side under cover
Wiring clamp
Wiring from the starter
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring and nut
Starter connector and wire clamp
Right side engine cover
Radiator reservoir and hose
Battery and tray

2. Check the cooling system and top off if necessary.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery
Engine under covers
Wiring from the starter terminals
Starter mounting bolts
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring
Engine under covers


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable
Front engine undercover
Starter wiring harness connectors
Starter mounting bolts
Starter motor


To install:
1. Install or connect the following:
Starter motor. Tighten the bolts to 28 ft. lbs. (37 Nm).
Starter wiring harness connectors
Front engine undercover
Negative battery cable

Hope help with this (remember rated and comment).

Mar 11, 2010 | 2003 Toyota Corolla

1 Answer

I need to know how to get the bolts off a nissan pathfinders starter motor


Nissan Pick-ups and Pathfinder 1989-1995
Starter - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter.
e757468.jpg
Fig. 1: Starter removal on 4WD-6-cylinder engine


4643c02.jpg
Fig. 2: Starter removal on 2WD-6-cylinder engine
  1. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.

  2. Unfasten the remaining electrical connections at the starter solenoid.
  3. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out.
To install:
  1. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  2. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  3. Install all remaining components in reverse order of removal.
  4. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.

Also can check here other DIY.

Hope helped with this (remember rated and comments this help).

Mar 03, 2010 | 1995 Nissan Pathfinder

Not finding what you are looking for?
1996 Chevrolet S-10 Pickup Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...