Question about 2003 Ford Ranger Regular Cab

Open Question

How do I remove the timing cover on a 2003 Ford Ranger?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jaysonemanme
  • 500 Answers

SOURCE: I just replaced the front cover of a 2003 Ford, Ranger, 2.3

there are no timing specs for that vehicle, the vehicle pcm does all of that. always mark your gears and chains when you take them off. if you just replaced the cover and thats it, there should be no reason why you would have to set the timing-

Posted on May 19, 2009

Ad
latoss101
  • 47 Answers

SOURCE: 2003 ford ranger transmission removal

you mite need a crows foot wrench.

Posted on Jan 03, 2009

davesmith_37
  • 94 Answers

SOURCE: where is the pcv valve located on a 2003 ford ranger

  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Posted on Feb 27, 2009

    • 257 Answers

    SOURCE: 2003 Ford Ranger, 5 speed manual. Sometimes I

    if you have a slave cylinder on it my not be working right,, if you have levers maybe a brushing wearing out cause wobble

    Posted on Aug 12, 2009

    Testimonial: "Thanks, I'll check it out."

    • 33 Answers

    SOURCE: removal and install timing belt 1994 ford ranger/

    Depends on the engine.

    Posted on Oct 10, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Engine Timing marks on a 4.0 ford ranger on a 2005


    Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

    Nov 02, 2011 | 2005 Ford Ranger

    1 Answer

    Changing clutch on a 2003 ford ranger how do I


    Well to start, you need to remove the shifter from the transmission. Then remove the driveshaft. Then unplug the plugs from the side of the transmission and disconnect the clutch fluid line. Then remove the crossmember. Unbolt the bellhousing bolts. Then have a friend help you remove the transmission. Then unbolt the clutch.

    Jul 09, 2010 | 2003 Ford Ranger Regular Cab

    2 Answers

    Does a 2003 ford ranger 2.3 liter have a chain, gear, or timing belt?


    The 2.3 uses a timing belt with an tension idler adjustment. Replacement is straight forward, just make sure to mark upper and lower cog pulleys before removing the old belt so that you can keep the timing in sync.

    Apr 26, 2010 | 2003 Ford Ranger Regular Cab

    1 Answer

    How to change timing belt on a 1987 ford ranger 2.0L 4C 5speed


    You need to get a manual. Try the Haynes manual for your car. Try autozone; generally available for around $20. This is not the type of thing that can be covered here in enough detail to do you any good.
    Buy new timing belt. Disconnect negative battery cable. Remove timing belt cover. make sure cylined #1 is set at TDC. making sure all componets are properly alligned and losen tensioner to remove old timing belt. Install new timing belt. Tension belt, ensure all components are alligned properly, replace timing belt covers and reconnect battery.

    Feb 21, 2010 | 1987 Ford Ranger

    1 Answer

    I just replaced the front cover of a 2003 Ford, Ranger, 2.3


    there are no timing specs for that vehicle, the vehicle pcm does all of that. always mark your gears and chains when you take them off. if you just replaced the cover and thats it, there should be no reason why you would have to set the timing-

    May 18, 2009 | 2003 Ford Ranger Regular Cab

    1 Answer

    Ford Ranger PCV valve.


    should be on the valve cover... goes into the cover thru a rubber gromet with a vacuum hose attached.

    Robert

    Jan 26, 2009 | 2003 Ford Ranger Regular Cab

    1 Answer

    Does a ford Ranger have a PCV valve???


    it should be on top of the valve cover.. all cars and trucks have them but sum and not many have 1's that never need to be replace..

    Jan 25, 2009 | 2003 Ford Ranger Regular Cab

    1 Answer

    Where is the PCV Valve Located ???


    okay i'm not 100% sure but it should be on top of the vavle cover or near the intake

    Jan 19, 2009 | 2003 Ford Ranger Regular Cab

    1 Answer

    2003 ford ranger transmission removal


    you mite need a crows foot wrench.

    Jan 03, 2009 | 2003 Ford Explorer Sport

    Not finding what you are looking for?
    2003 Ford Ranger Regular Cab Logo

    Related Topics:

    114 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5520 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...