Question about 1999 Porsche Boxster

1 Answer

In need of torque settings for a porsche boxter

What are the head bolt torque settings for a t reg porsche boxter 2.5 6 cylinda

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Porsche Master
  • 907 Answers

Moisten bolts with engineoil,
1st step tighten to 23 ftlb
2dn step loosen all bolts
3rd step tighten to 15 ftlb
4th step add 60 dgrees
5th step add 60 dgrees

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Please confirm torque for 95 accent 1.5 head bolts.Thanks


Already answered on Fixya

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.

Cylinder head torque settings for 1995 hyundai accent 1 5

Feb 02, 2017 | Hyundai Accent Cars & Trucks

1 Answer

I HAVE AN AUDI A4 TDI X REG, IVE GOT THE CYLINDER HEAD OF. WHAT IS THE HEAD BOLT TORQUE AND IS THERE A SEQUENCE TO TORQUE THEM CHEERS.


Audi A4 1.9 TDI-PD (Pumpe Duse)

Cylinder head tightening sequence:

tdisline_853.jpg
Renew bolts!

Torque settings:
1. Stage 1 = 40 Nm
2. Stage 2 = 60 Nm
3. Stage 3 = 90 Degrees
4. Stage 4 = 90 Degrees

Please do rate my response. Thanks!

Sep 01, 2011 | Audi A4 Cars & Trucks

1 Answer

Cylinder head torque settings for 1995 hyundai accent 1.5


According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.

Feb 14, 2011 | Hyundai Motor 1995 Accent

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

1 Answer

Hi iv got an escort 1.8 16v zeetec its r reg and iv had the head re conditioned i need 2 put the head bck on but i need to no the torqe setting can u help me thankyou.


hi yes here are the torque settings

stage 1 is 25nm
stage 2 is 45nm
stage 3 is turn 105 degrees

try leaving about 10 mins between each torque so it can settle also you have to tighten them in sequence and make sure you use new head bolts as these are the stretch type and if you are using the old ones there could be a chance of one snapping, just a little advice..hope this helped

Feb 15, 2010 | 1998 Ford Escort

2 Answers

How to open/access Porsche Boxter engine (2000)


lower hood back until front edge of hood is above drivers head when seated in car, then release cables holding rear edge of hood to body (one each side clipped onto two ball joints, and unclip long plastic rain channel along rear of hood. lift rear frame/rear window up to vertical behind driver. remove compartment and carpet held by four 1/2 turn screws to uncover engine cover, this is released by turning locking clips 1/2 turn

Jul 01, 2009 | 2000 Porsche Boxster

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Angle Torque settings head bolts


Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Jan 28, 2009 | 2000 Renault Sportwagon

1 Answer

Cylinder head ford zetec escort p reg


Stage 1 = 15Nm
Stage 2 = 40Nm
Stage 3 = Plus 90 degrees or quarter of a turn. Good tip is to mark all the bolts after initial torque setting with tip-ex , i.e. all to the front of the car. When you finish they should all point towards the timing belt.
This is also a good way to make sure you don't miss one or tighten one twice if you are distracted since it is not a torque setting. New bolts should be used by the way as they are stretch bolts. Timing of cams - remove cam cover and you will see a slot on the end of the cams. Opposite end from belt. You need to slip a piece of 5mm flat bar or a long 5mm allen key into then so that the bar rests on the face of the head. Engine should be a tdc.
cheers John

Dec 17, 2008 | 1998 Ford Escort

4 Answers

Head bolts torque settings


According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Oct 26, 2008 | 1995 Land Rover Discovery

Not finding what you are looking for?
1999 Porsche Boxster Logo

Related Topics:

612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

907 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...