Question about 1992 Toyota Celica

1 Answer

Uninstall motor starter how to - 1992 Toyota Celica

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 977 Answers

Disconnect the battery lead from the starter plus any other wires undo the bolts from the starter motor flange & the starter motor should pull straight out if there is nothing the way,if anything is in the way it will have to be removed first.....hope this helps.....cheers

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 pontiac montana and am trying to figure out how to change the starter.


STARTER REPLACEMENT (ENGINE ELECTRICAL) Document ID# 688149 Starter Replacement

Removal Procedure

Important: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.
  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.


  3. Remove the starter motor BAT terminal nut and electrical leads.
  4. Remove the starter motor S terminal nut and electrical lead.
  5. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  6. Remove the starter motor bolts.
  7. Remove the starter motor.

Installation Procedure



  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in Cautions and Notices.
  3. Install the starter motor bolts.Tighten:
    Tighten the starter motor bolts to 47 [n-m] (35 lb ft).
  4. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  5. Install the starter motor S terminal electrical lead and nut. Tighten:
    Tighten the starter motor solenoid S terminal nut to 3 [n-m] (27 lb in).
  6. Install the starter motor BAT terminal electrical leads and nut. Tighten:
    Tighten the starter motor solenoid BAT terminal nut to 10 [n-m] (89 lb in).
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.

Aug 05, 2016 | 2001 Pontiac Montana

1 Answer

I need the part number for the starter motor for my Pajero


You don't need the part number as it depends on the maker of the starter motor.

  • mitsubishi pajero starter motor ' Cars ... - Gumtree www.gumtree.com.au/s-automotive/mitsubishi+pajero+starter+motor/k0... Find mitsubishi pajero starter motor ads in our Cars & Vehicles category. Buy and sell almost anything on Gumtree classifieds.
  • MITSUBISHI PAJERO IO STARTER MOTOR ' Starter Motor ... www.startermotoralternator.com/.../mitsubishi/pajero-io/starter-motor MITSUBISHI PAJERO IO STARTER MOTOR - Extensive Starter Motor / Alternator catalogue searchable by make, model, year and engine size.
  • pajero starter motor ' eBay www.ebay.com.au > Search > pajero starter motor Find great deals on eBay for pajero starter motor pajero diesel starter motor. Shop with confidence.
  • mitsubishi pajero starter motor ' eBay www.ebay.co.uk > Search > mitsubishi pajero starter motor Find great deals on eBay for mitsubishi pajero starter motor mitsubishi pajero 2.8 starter motor. Shop with confidence.
  • Mitsubishi Starter Motors - Auto Electrics Direct - buy ...
  • www.autoelectricsdirect.com.au/index.php?_a=category&cat_id=15&... buy now online auto electrical parts, online shop,starter motors, alternators,smart solenoid, hid lighting, air- conditioning parts and accessories ,best quality ...
  • Pagination
  • MITSUBISHI COLT PAJERO CANTER L300 EXPRESS HYUNDAI SONATA LANTRA 12V 1 4...

    May 20, 2016 | 1994 Mitsubishi Pajero

    1 Answer

    I need to find out how to take off and put on a starter on a 2004 chevy tracker


    TESTING WARNING
    During the following test, the starter motor must not be energized for longer than 5 seconds, otherwise you run the risk of burning out the starter motor coil.
    1. Remove the starter motor from the vehicle.
    2. Detach the field coil lead from terminal M on the starter motor.
    3. Using jumper wires, connect a 12 volt battery to the starter motor so that the negative battery terminal is attached to the starter motor housing and to solenoid terminal M, and that the positive battery terminal is connected to starter motor solenoid terminal S. The starter motor plunger should move outward; if it does not, replace the solenoid with a new one. Fig. 1: To test the solenoid plunger, first detach the field coil lead from alternator terminal M, then attach a 12 volt battery to the starter motor as shown . . . 90882g50.gif
      Fig. 2: . . . then detach the negative jumper wire from terminal M. The plunger should remain extended 90882g51.gif
      Fig. 3: Detach the other negative lead from the starter motor housing. The solenoid plunger should now retract to its normal resting position 90882g52.gif
      Fig. 4: Use an ammeter to measure the amount of current draw the starter motor uses 90882g53.gif

    4. Detach the negative battery jumper wire from terminal M on the starter motor solenoid, and check the plunger for movement. The plunger should remain extended; if the plunger returns to its resting position, replace the solenoid with a new one.
    5. While observing the solenoid plunger, detach the negative battery lead from the starter motor housing. The plunger should return to its normal resting position; if it does not, replace the solenoid with a new one.
    6. Reattach the 12 volt battery and install an ammeter to the starter motor as shown in the accompanying illustration. The starter motor should rotate smoothly and steadily with the pinion gear moving out, and the ammeter should display less than 60 amps at 11.5 volts (Samurai models), or 90 amps at 11 volts (Sidekick, Tracker, X-90 and Sidekick Sport models). If the ammeter does not display the specified values, or if the starter motor does not operate smoothly and steadily, replace the starter motor with a new one.
    ---
    REMOVAL & INSTALLATION
    1. Disconnect the negative battery cable.
    2. If necessary for added under-vehicle clearance, apply the parking brake, block the rear wheels, then raise and safely support the front of the vehicle on jackstands.
    3. From beneath the vehicle, label and detach all wiring from the starter motor solenoid terminals.
    4. Remove one of the two starter motor mounting bolts and loosen the other bolt until it can be turned by hand, then support the starter motor with one hand while removing the last starter motor mounting bolt.
    5. Lower the starter motor down and away from the engine and transmission. To install:
    6. Hold the starter motor in position and install the two mounting bolts. Tighten the two bolts securely.
    7. Reattach all applicable wiring to the starter motor solenoid. Ensure that the wiring terminals and connectors are clean and free of corrosion.
    8. If necessary, lower the vehicle.
    9. Connect the negative battery cable.

    Oct 23, 2010 | Chevrolet Tracker Cars & Trucks

    1 Answer

    Starter solinoid replacement enstruction


    SOLENOID REPLACEMENT
    (see Figures 5, 6 and 7)

    Prior to removing the solenoid from the starter motor unit, matchmark the solenoid-to-starter motor housing position, as shown in the accompanying illustration.
    1. Remove the starter motor from the vehicle.
    2. Detach the solenoid-to-starter motor wire from the solenoid terminal.

    Do not disassemble the solenoid; if the solenoid is defective, replace the entire unit with a new one.
    1. Remove the two attaching screws, then slide the solenoid out of the starter motor housing flange.
    9b9a219.jpg

    Fig. 5: Before removing the starter motor solenoid, matchmark the solenoid-to-starter motor housing relationship

    44d3238.jpg

    Fig. 6: Disconnect the field coil lead from the solenoid by loosening the retaining nut ...

    e357fdb.jpg

    Fig. 7: ... then remove the two attaching screws and separate the solenoid from the motor housing


    To install:
    1. Inspect the solenoid plunger joint for wear or other damage. Replace it, if damage is evident.
    2. Apply Suzuki Super Grease A (99000-25010) or equivalent, to the solenoid plunger and to the tip of the lever arm (inside the starter motor-to-solenoid housing hole).
    3. Insert the solenoid into the starter motor housing, ensuring that the matchmarks made during removal are aligned.
    4. Install and tighten the two attaching screws securely.
    5. Attach the starter motor-to-solenoid wire to the solenoid terminal.
    6. While the starter motor is removed form the vehicle, perform the testing procedure to ensure that the new solenoid functions properly.
    7. Install the starter motor.

    Hope this help (remember rated and comment this).

    Mar 23, 2010 | 1994 Geo Tracker

    2 Answers

    98 Durango will not turn over, replaced battery, battery cables, had started checked. Just get a clicking noise at starter like a dead battery. Will start some times.


    Sounds like a bad connection. Clean all the connections first then if you have a clicking sound coming from the PDC (fuse box) on the drivers side under the hood then it sounds like you have a bad starter .
    As the relay is clicking that means the ignition switch is good. Just insure that the relay is good. There is a spare in the PDC you can swap and check out so its the starter Starter/solenoid combo.take your volt meter and check battery volts while the starter is engaged, if you see very little change from the static voltage it's likely the starter bendix is being egaged into the ring gear but the high current side of the starter is not working, this is likely due to a dirty or worn commutator or worn brushes in the starter motor. If you do see a larger drop in voltage( say down to under 9.5volts) you more than likely have a current flow issue, possibly a weak cell in the battery, or a shorted starter motor winding.My best recomendation would be to remove the starter motor, and the battery, take them in with you to your local parts house and have them both tested, most parts stores will perform these tests for free, on the possibility that hey can sell you something.
    STARTER MOTORREMOVAL:-1. Disconnect and isolate the battery negative cable.2. Raise and support the vehicle.3. Remove the nut and lock washer securing the starter motor to the mounting stud on the transmission torque converter housing Starter Motor Remove/Install4. While supporting the starter motor with one hand, use the other hand to remove the upper mounting screw from the starter motor.5. Slide the automatic transmission cooler tube bracket forward on the tubes far enough for the starter motor mounting flange to be removed from the lower mounting stud.6. Move the starter motor towards the front of the vehicle far enough for the nose of the starter pinion housing to clear the transmission torque converter housing. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.7. Tilt the nose downwards and lower the starter motor far enough to access and remove the nut that secures the battery positive cable connector eyelet to the solenoid battery terminal stud. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.8. Remove the battery positive cable connector eyelet from the solenoid battery terminal stud. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.9. Disconnect the battery positive cable wire harness connector from the solenoid terminal connector receptacle. Always support the starter motor during this process, do not let the starter motor hang from the wire harness.10.Remove the starter motor from the engine compartment. --This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

    Feb 22, 2010 | 1999 Dodge Durango

    1 Answer

    2001 ford focus zx3 starter replacement instructions


    2.0L DOHC Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Remove or disconnect the following:
      • Negative battery cable
      • Air cleaner outlet tube
      • Lower starter motor bolt
      • Two starter motor upper bolts
    3. Slide the starter motor from its mounting until you can gain access to the wiring.
      • Integral connector
      • Starter motor
    To install:
    1. Install or connect the following:
      • Integral connector and tighten the retaining nuts to 61 inch lbs. (7 Nm)
    f20d98a.gif
  • Starter motor to its mounting
  • Two starter motor upper bolts and tighten to 15–20 ft. lbs. (20–27 Nm)
  • Lower starter motor bolt and tighten to 15–20 ft. lbs. (20–27 Nm)
  • Air cleaner outlet tube
  • Negative battery cable
  • Dec 06, 2009 | 2001 Ford Focus

    1 Answer

    Where is starter located and how to remove it , for a dodge caravan 1998,3.3l


    Starter - Removal & installing
    1. Disconnect the negative battery cable.
    2. Raise and safely support the front of the vehicle securely on jackstands.
    3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
    4. Remove the B+ nut and wire from the starter motor terminal.
    5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
    6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
    To install:
    1. If equipped, hold the starter motor spacer in position.
    2. Install the starter motor into position on the vehicle.
    3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
    4. Engage the solenoid wiring connector onto the starter terminal.
    5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
    6. Lower the vehicle.
    7. Connect the negative battery cable.
    8. Verify starter motor operation.
    020fef8.jpg

    Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

    98933b2.jpg

    Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

    e2afde4.jpg

    Remove the starter motor from the vehicle


    The starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.

    Hope helped with this (remember rated this help) Good luck.

    Nov 18, 2009 | 1998 Dodge Grand Caravan

    1 Answer

    Replace an alternator on a 2005 chevy venture (instructions)


    REMOVAL PROCEDURE

    IMPORTANT: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.

    1. Disconnect the battery ground (negative) cable from the battery.
    2. Raise and suitably support the vehicle. Refer to Vehicle Lifting.
    3. Remove radiator air baffle assembly.
    4. Remove the starter motor BAT terminal nut and electrical leads.
    5. Remove the starter motor S terminal nut and electrical lead.
    6. Remove the torque converter co
    7. Remove the starter motor bolts.
    8. Remove the starter motor.
    INSTALLATION PROCEDURE
    1. Install the starter motor.
    2. Install the starter motor bolts. Tighten the starter motor bolts to 47 N.m (35 lb ft)
    3. Install the torque converter cover.
    4. Install the starter motor S terminal electrical lead and nut. Tighten the starter motor solenoid S terminal nut to 3 N.m (27 lb in).
    5. Install the starter motor BAT terminal electrical leads and nut. Tighten the starter motor solenoid BAT terminal nut to 10 N.m (89 lb in) .
    6. Install radiator air baffle assembly.
    7. Lower the vehicle.
    8. Install the battery ground (negative) cable to the battery.

    Jul 25, 2009 | 2005 Chevrolet Venture

    2 Answers

    91 stanza starter motor location...??


    its bolted up to the flywheel on the side or back of the motor.

    Jun 04, 2009 | 1991 Nissan Sentra 2 Door

    1 Answer

    How do you replace starter motor on a 2002 explorer 4x4 4.6L engine?


    YOU HAVE TO STRIP SOME OF THE TOP LAYERS LIKE AIR FILTER BOX THROTTLE CABLE ECT... ITS AT THE TOP PART OF THE MOTOR CLOSEST TO THE FIRE WALL 3 BOLTS HOLD IT IN PLACE.
    *REMEMBER TO DISSCONNECT THE BATTERY CABLE B4 YOU START YOUR PROJECT. IF ALL GO'S SMOOTH YOU SHOULD UNINSTALL AND REINSTALL IN LESS THAN 1 HOUR.

    Feb 23, 2009 | 2002 Ford Explorer

    Not finding what you are looking for?
    1992 Toyota Celica Logo

    Related Topics:

    79 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    Marvin
    Marvin

    Level 3 Expert

    81400 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...