Question about Mazda MAZDA6

1 Answer

I have Mazda 6, 2004 model , it is jerking while driving above 60 Km speed, and stops while running frequently? I have changed the spark plugs and cleaned fuel pump, even then the problem persist

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 415 Answers

It seems the cables connecting your spark plugs to the distributor may be worn or damaged try replacing them and see if the problems persist

Posted on Jul 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The problem: intermittently it hiccups, jerks and


check the spark plug wires. one or more may be bad . if you want to check it yourself get a spray bottle with water in it and spray the wires if you see sparks they are bad

Sep 06, 2013 | 1999 Mazda Protege

1 Answer

Jerking / hesitation


your problem must be your connection of the wire try to fix them all.

Oct 30, 2012 | Cars & Trucks

1 Answer

How frequent in changing engine oil


You should do this each 6 months or each 6000 km in severe conditions, which are one or more of......... frequent towing, all short-run driving, all stop-start driving, frequent dusty conditions or extreme heat.
For good conditions, none of the above, Toyota says you can stretch it to half the above frequency but I would not. Oil is cheaper than a new motor.
For the average driver doing a bit of all this I'd say every 6 months or 10000Km, and change the oil filter at the same time.

Apr 24, 2012 | 2000 Toyota Camry

1 Answer

Just got the coil and spark plug changed as the car was sounding and driving abit rough. seemed to do the job, but after week i took it on a slighlty longer drive on the highway (40 mins) and it went back...


I would say check your Mass Air Flow sensor. Take it off, and clean it really good, and run a can of Sea Foam through the tank. You can get it at any parts store. It is an additive for cleaning your engine and helps a lot for stuck lifters and gunk. If that doesn't help, I would say the fuel system would be your next step. Jerking tells me that air/fuel mix is disrupted, or your spark which from what you are saying has been eliminated.

Mar 07, 2011 | 1997 Ford Expedition

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

4 Answers

Mpv 2001 misfires only between 60 to 80 km/h


It may be a throttle position sensor. Also, try a fuel injection cleaner, like Lucas brand.

Aug 26, 2009 | 2001 Mazda MPV

4 Answers

Where is the transimisson filter located in mazda 626 /2000?


The automatic transmission filter is located inside the transmission pan.

Mar 07, 2009 | 1999 Mazda 626

1 Answer

Toyota Camry 2.2 1994 model


Have your mechanic check the timing belt marks and the condition of the belt itself. If the cam is retarded a 1/2 tooth due to age, this will create this problem as well. Have him also check for any vacuum leaks at the intake.

Sep 01, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...