Question about 1998 Ford Expedition

1 Answer

Problem have a 1998 ford expendition the manifold bolt & exhaust bolt need to be replaced need to replace them were could I buy replacement part

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Ford Master
  • 16,575 Answers

Any auto store or speed shop can get or have instock

Posted on Jul 28, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need to remove the exhaust manifold on the right side of a 94 4.9l engine in a cadillac deville. It has a broken bolt in the exhaust. What is involved in removing the manifold?

I suggest you use all new exhaust manifold hardware and torque new bolts to 20 Ft Lbs.
4.5L and 4.9L Engines
Disconnect the negative battery cable. Remove the air cleaner. Remove the exhaust crossover pipe. Disconnect the oxygen and coolant temperature sensors. Remove the catalytic converter-to-AIR pipe clip bolt. Remove the upper manifold-to-cylinder head bolts. Raise and safely support the vehicle. Disconnect the converter air pipe bracket from the stud and remove the converter-to-manifold exhaust pipe. Support the engine cradle with screw jacks and remove the rear cradle bolts. Loosen the front cradle bolts and slightly lower the Engine cradle. Remove the remaining exhaust manifold-to-cylinder head bolts, the AIR pipe, and the manifold. Clean the gasket mounting surfaces.
To install:
Install the exhaust manifold and replace the AIR pipe. Tighten the manifold mounting bolts to 16-18 ft. lbs. (21-24 Nm). Install the manifold-to-converter exhaust pipe and replace the converter air pipe bracket to the stud. Raise the Engine cradle and install the rear cradle bolts. Tighten to 75 ft. lbs. (102 Nm). Lower the vehicle. Replace the upper manifold-to-cylinder head bolts. Replace the converter air pipe to AIR pipe clip bolt. Connect the coolant temperature and oxygen sensor connectors. Replace the exhaust crossover pipe. Replace the air cleaner and connect the negative battery cable. Start the Engine and check for leaks.

Mar 28, 2017 | Cadillac Cars & Trucks

1 Answer

98 ford windstar intake manifold torque specs

Intake torque specs ' > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Exhaust manifold removal procedure

It doesn't have to come off but it will make your life a hell of a lot easier to access the exhaust bolts if it does!!!!

Sep 21, 2012 | Ford Tempo Cars & Trucks

1 Answer

Im buying a car through a private sale and he said the 2000 Ford Focus has an exhaust leak. how do you fix that? is that expensive?

It really depends on where the exhaust leak is. If it's in the piping or the muffler, then it won't be to bad fix with some over the counter stuff available at your local parts store. However, if the leak is in the manifold, then you could be lookin at replacing an exhaust manifold gasket. If it is in fact coming from the exhaust manifold, try tightening up the bolts. If work has been done on it before, there is a good chance one or two of the bolts could be loose or improperly torqued. The other thing to look for is a warped manifold, but that usually only occurs if the engine has gotten really hot. I hope this helps in some way.

Mar 23, 2011 | 2000 Ford Focus

1 Answer

How to replace an exaust manifold on a 1991 ford bronco 302-v8

start by removing nuts from exhaust pipe on the underside, then remove the 8 bolts that hold manifold to engine and pull it up. make sure when reinstalling you inspect the gasket and replace if needed. there is also a circular gasket between the exhaust manifold and the exhaust pipe, inspect and replace if needed. reverse for install.

Jun 03, 2010 | 1991 Ford Bronco

1 Answer

How to replace exhaust manifold wher it connects to exhaust pipe bolts rotted out


Aug 15, 2009 | 1998 Ford F150 Regular Cab

1 Answer

On a 1995 GMC sierra P/U 5.0L engine. The

NO , just replace the the gasket and exhaust bolt, just make sure you buy a stainless bolt, there not much more but they will out last the truck. and might as well replace the drive's side too since your working on it. Good luck and hope this helps. 

Jul 01, 2009 | 1995 GMC Sierra C1500

2 Answers

1988 Ford F150 exhaust manifold leak repair section

Apr 02, 2009 | 1988 Ford F 150

1 Answer

First start up, oder of gas and exhaust fumes

Probably one of your exhaust manifolds,I just had my right side one replaced this summer in my 1998 Mountaineer 5.0,basically the Mountaineer is the same as an Explorer.The same can happen with the V-6 model.the repair is around $325,depending where your shop buys the replacement manifold.You can find them on e-Bay,I just didn't want to deal with the rusty manifold bolts possibly breaking off,having to drill them out etc,etc.Have it done and it's their problem! Do yourself a favor get a quote first,I saved $75 by checking out a few different shops.Unless you have a THICK wallet don't take it to the dealer.

Nov 22, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
1998 Ford Expedition Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides